BIXOLON SRP-330II Скачать руководство пользователя

Страница: 15 / 125

SRP-330II/332II

Rev. 1.00

BIXOLON

- 15 -

DLE DC4

Function:

Generate pulse at real-time

Code:

ASCII

DLE

DC4

Hex

Decimal

Range:

n = 1, m=0,1,

1 ≤ t ≤ 8

Default:

None

Description:

■

Output the pulse specified by t to connector pin m as following:

Connector pin

Drawer kick-out connector pin 2

Drawer kick-out connector pin 5

■

This command generates the drive pulse to connector pin m with pulse width defined by t as following:

•

Drawer kick-out connector pin 2 is selected with m=0 while pin 5 chosen for m=1.

•

Pulse ON time is [t x100 ms] and OFF time [t x100 ms].

Remarks:

■

Upon receiving this command, the printer outputs the drive pulse to the specified connector pin.

■

The real time command is stored into the receive buffer and executed with higher priority than other commands.

Differences:

None

Содержание SRP-330II






























































































































Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды

BIXOLON SRP-330II, Руководство по управлению

Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды