BIRO 44 страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 36

background image

CLEANING

SHARP MOVING BAND TYPE SAW BLADE

TO AVOID SERIOUS PERSONAL INJURY

ALWAYS

Turn Off, Unplug From Power Source and Perform Lockout/Tagout Procedure to This

Machine

BEFORE

Cleaning or Servicing.

ONLY

Use Recommended Cleaning Equipment, Materials and Procedures.

NEVER

Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other

Electrical Components.

ALWAYS

Thoroughly Clean Equipment at Least Daily.

CLEANING THE BIRO POWER CUTTER:

Disconnect electrical power to the machine before cleaning. Parts to be removed have been made accessible and can
be removed without tools. Notice in the drawing below that all parts are numbered. Each part should be removed for
cleaning in the numbered sequence shown. To ensure cleaner cuts, keep the parts on the cleaning system in good
condition. Parts on the cleaning system which should be checked weekly, and changed as required are as follows:
Wheel Cleaners (Part No. 179), Saw Cleaners (Part No. 131), Saw Guide in Stationary Bar (Part No. 119A), Upper Saw
Guide (Part No. 602B), Lower Blade Back-Up Guide (Part No. 605) and Nylon Filler (Part No. 177).

8

«
...
10
11
12
13
14
...
»

Содержание 44





































Отзывы:

Нет отзывов

Похожие инструкции для 44

1000 4.5 Hot cutter

Бренд: TRC Страницы: 67

Бренд: Dimas Страницы: 23

Бренд: Performance Tool Страницы: 2

Бренд: Dremel Страницы: 88

Бренд: LaserPro Страницы: 59

Бренд: Secabo Страницы: 21

Бренд: HSS Hire Страницы: 2

Бренд: CAB Страницы: 26

Бренд: HSGM Страницы: 6

Бренд: Baileigh Industrial Страницы: 48

Бренд: Zenoah Страницы: 40

Бренд: Yueming Страницы: 70

Бренд: Huskie Tools Страницы: 16

Бренд: Huskie Tools Страницы: 16

SRM-210 - 10-05

Бренд: Echo Страницы: 32

Бренд: Spedo Страницы: 51

Бренд: Hitachi Страницы: 34

Бренд: Hitachi Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды