BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 65

background image

Measure Match Mode

18

6.

Connect the SiteHawk to the device under test.

7.

Wait 10 Seconds for the sweep to update.

Interpreting the Measurement

The graph below shows a typical Match Measurement for an antenna system.

Figure

9

Interpreting Match Measurement

The graph contains the following elements:



Vertical grid scale (y axis) displays dB and ratio data values.



Horizontal grid scale (x axis) displays frequency, time or distance data
values.



The measured value of the Markers (1 and 2 in this example).



Trace number (Tr1) and color is used identify the trace.



When scanning duration is more than 1 second, a current position
indicator will appear.

Cable Loss Measurement

Ensure that the cable being tested is unterminated (not connected to anything
at the far end).

Note:

Ensure the cable is disconnected from any RF power source.

Note:

Ensure the frequency band of the system is known.

«
...
25
26
27
28
29
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

Бренд: Vcheck Страницы: 31

Бренд: Eagletone Страницы: 2

Бренд: 3B6 Страницы: 30

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: OBDPROG Страницы: 8

Pasport PS-2138

Бренд: Pasco Scientific Страницы: 26

Бренд: Autometers Systems Страницы: 16

Бренд: RIDGID Страницы: 18

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Sensitech Страницы: 2

Бренд: Hanna Instruments Страницы: 11

Radon Scout Home

Бренд: SARAD Страницы: 2

Бренд: BART Страницы: 24

Бренд: Geokon Страницы: 19

Weather Oracle MKIII

Бренд: RainWise Страницы: 17

Бренд: Lancol Страницы: 7

Бренд: Würth Страницы: 188

Бренд: Danfoss Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды