BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 15

Страница: 15 / 65

Introduction

Power

The SiteHawk Analyzer has an internal, rechargeable, lithium-ion battery pack.

CAUTION

Only use the supplied AC adapter to charge the unit.

The unit cannot be charged through the USB port (i.e. from a laptop).

Charging from a power source other than the supplied charger may damage

the battery.



The unit will operate for approximately 10 hours with a full charge.



Recharging time, from a full discharge, is approximately 5 hours with
unit powered off.

Note:

When the unit is received the battery may not be fully

charged. An AC adapter should be used when operating the unit for
the first time.

Powering On

Press Power button for 5 seconds.

Note:

Unit will complete power-up in approximately 30 secs.

Powering Off

Press Power button for three seconds.

Note:

A Device Options dialog will open.

Select Power Off.

Note:

A Power Off dialog will open.

Press Ok.

Sleep Mode

Press and release Power button.

Note:

The display screen will be shut down. The SiteHawk Ana-

lyzer will still be on.

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды