BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 14

Страница: 14 / 65

Bird SiteHawk Operation Manual

Measurement Capability



Fast measurement speed



Seven user-selectable trace capture options: 51, 101, 201, 401, 801,
1601, or 3201 data points per sweep



Adjustable pass/fail limit with visual indicator



16 GB of internal flash memory for storing thousands of traces and
setups



X and Y scales and units are user adjustable



Six markers, direct or difference measurement



Measure relative to limit line or recalled trace



Measurement hold to temporarily store a trace



Frequency Start/Stop or Center/Span frequencies



Return Loss [dB], Cable Loss [dB], SWR [ratio], DTF SWR [ratio] or DTF
Return Loss [dB]

Connectors and Ports

Figure

SK-4500 Connectors and Ports

Antenna Test Port

Female N connector for connecting to the antenna. Use
a phase-stable cable for best results.

Charger Input

Input connector for charging the SK-4500 using the
supplied charger.

USB-C 3.0 Type

USB device port for connection to a USB Drive or Bird
Power Sensor.

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды