arrays. The switch arrays are
the switch banks located in
the top left corner of the unit
to the left of "Recordings" and
to the right of "Mode Settings".
A switch is ON if the switch is
moved to the right-hand side. The switch is OFF if
it is moved to the left-hand side.
RECORDING SWITCHES
The Recordings switches are
the first eight switches in the top
switch array. Each switch has
a recording number to the right
of it that corresponds with the
bird descriptions listed on the
foil label affixed to the Memory Card with Sound
Chip assembly.
MODE SETTING SWITCHES
The Mode Setting switches set
the
various modes of opera-
tion: such as the amount of
time between playing bird dis-
tress calls, when the unit will operate (day only,
night only, or 24 hours), and whether the unit will
operate in the Random Mode or Normal Mode.
Switch
Mode or Function
1
Sets the Time-Off Period
2
Sets the Time-Off Period
3
Sets the Time the unit plays
4
Sets the Time the unit plays
5
Turns Random Mode On or Off
TIME OFF SWITCHES
The two Time Off switches
are located just below the
Recording switches in the
switch array. When the unit is
set to one of the various Time Off modes, the unit
will delay a number of seconds or minutes between
recorded sounds. Please note that the unit will play
all of the selected recordings (either sequentially
PRIOR TO INSTALLATION
Your complete Bird Gard
®
Super Pro AMP kit includes
a con trol unit, 40-watt solar
panel, ba t t ery cable with
clips and a 20-spea ker tower.
Open the con trol unit by lift-
ing the two latches on the
side of the enclosure.
Prior to operation, route the
speaker and power cables
from their respective jacks
on the control panel down
through the cable strain
relief in the lower part of the
enclosure.
IM
POR
TANT: Be
certain that
the power switch is in the OFF
po si tion and the volume control is set
to the minimum (LOW) vol ume level
( coun ter clock wise) as shown in Fig. 1
when powering up the unit.
SETUP AND INSTALLATION
1) Use the mounting hard-
ware (included) to mount
the control unit box to a
wall, post, pole or other
vertical surface.
2) Attach the battery cable
as sem bly to a 12V battery
(not included) matching
the positive and negative
terminals. The other end
of the cable comes pre-
installed into the power
terminal block. Attach the
two speaker wires from
Digital Bird Repeller
Fig. 1
Cable Strain Relief
Complete system shown
mounted on a pipe
with solar panel.
the 20-speaker tower to the speaker terminals
on the generating unit. Connect the solar panel
to the battery matching the positive and negative
terminals on both ends. (Fig. 2)
3) It is recommended to mount the 20-speaker
tower on a pole or surface that is aimed directly
and at the same level as the infected area.
4) Set the "Recordings" switches, "Mode Settings"
switches, Time Off switches, Time of Operation
switches and Random Operation switches to
the desired settings. (See “PRO GRAM MING
YOUR SUPER PRO AMP” for complete details
on how to program your bird repeller).
5) Make sure the volume setting is set to LOW (all
the way counterclockwise).
6) Slide the power switch to the ON position. The
unit may take a few seconds before starting.
7) Adjust the volume to the desired level.
8) Close the cover and latch shut.
PROGRAMMING YOUR SUPER PRO AMP
To program your Super Pro AMP unit you will
need a small screw driver, toothpick, or other small,
rigid object to toggle the switches in the switch
Control Unit
20-Speaker Tower
40-Watt Solar Panel
with Mounting Kit
12-Volt Battery (Not Included)
Inside Battery Box (Included)
And SunSaver 6 Voltage
Regulator (Included)
See Enlarged Photograph
At Right
+
-
SPEAKERS
12V BATTERY
Enlarged View of SunSaver-6
Solar Controller -- Voltage Regulator
Wiring Setup Diagram
Fig. 2
NOTE:
The Bird Gard Super Pro Amp features a replaceable Memory
Card with Sound Chip. You will notice that the sounds included on your
Bird Gard Super Pro Amp unit are listed on a silver foil label affixed to the
chip. To remove, simply pull Memory Card with Sound Chip straight out
from the embedded socket. Then insert a different Memory Card with
Sound Chip by pressing firmly straight into the socket.
