Bird Electronic Thruline 4020 Series Скачать руководство пользователя страница 50

Страница: 50 / 59

Bird 4421 RF Power Meter

Storage and Shipment (Cal Cart only)

Cover the unit before storing to keep out dust and dirt. It is not necessary to

install the shipping plug. Store in a dry, dust-free environment where the

ambient temperature will remain between –20 and +50 °C (–4 to +122 °F).
Before shipping the Bird Cal Cart, take the following precautions:

Remove the vent plugs and replace them with the shipping plugs.

Wrap the vent plugs with padding and tape them to the side of the

load for protection.

Note:

With the shipping plugs installed, it is not necessary to

empty out the coolant.

Repack in the original carton or contact Bird for a transit case.

Specifications, Cal Cart

To determine the model numbers of the Cal Cart components, refer to "About This
Manual" on page x. For load specifications, refer to the load manual included.

Note:

Certain sensors or connectors may be incompatible with

some models. Refer to "About This Manual" on page x for a list of avail-
able components, or contact Customer Service.

Max. Power

Under normal operating conditions, the Cal Cart’s maximum power is the

MINIMUM of the max. power of the sensor and the max. power of the load.

The following modifiers apply:

Above 65 MHz, derate the load’s max. power. See "High Frequency

Derating 1" on page 47.

Due to the wide variety of available connectors, frequency range and

maximum power may be reduced. Insertion loss is specified with female

N connectors. Choose connectors appropriate for the frequency and power

of operation.

Derate RF power by 2.5% for every 305m (1,000 ft.) above 1,520m (5,000 ft.).

Table 7-20 Bird Cal Cart

Frequency Range

Sensor dependent, 30 MHz max.

Power Range

Dependent on sensor, sensor connectors, and load

Connectors

Customer specified (See "Available Connectors" on page 49)

Dimensions

Short Cart
Long Cart

42”L x 20”W x 42”H (1067 x 508 x 1067 mm)
52”L x 20”W x 42”H (1321 x 508 x 1067 mm)

Weight, Nominal

Short Cart
Long Cart

175 lbs. (80 kg)
290 lbs. (114 kg)

Temperature Range

Operating
Storage

0 to +35 °C (32 to +95 °F)
–20 to +70 °C (–4 °F to +158 °F)

Altitude

1520 m (5000 ft.)

Humidity

85% noncondensing max

Calibration Cycle,
Nominal

1 year

CE Compliant. Refer to Declaration of Conformity for specific
standards.

Содержание Thruline 4020 Series




























































Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды

Bird Electronic Thruline 4020 Series, Инструкция

Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды