Bird Electronic Thruline 4020 Series Скачать руководство пользователя страница 46

Страница: 46 / 59

Bird 4421 RF Power Meter

11. Press dBm.

Note:

“dBm” should change to “SWR”.

12. Press FWD.

Note:

“SWR” should change to “FWD” and “ ” to “.0000 W” (or a

very low number).

13. Hold down MAX.

Note:

“.0000” should change to “1.0000”.

14. Release MAX.

Note:

“1.0000” should change to “.0000” (or a very low number).

15. Press LIGHT.

Note:

The back-light should turn on.

16. Press LIGHT.

Note:

The back-light should turn off.

17. Press s (up).

Note:

The power meter should change ranges each time it is

pressed until it reaches “0.000 KW”.

18. Press

(down).

Note:

The power meter should change ranges each time it is

pressed until it reaches “0.00 W”.

19. Turn the power meter OFF.

Repair

Front Panel (Cal Cart only)

Note:

If the power meter is mounted in a Cal Cart, to access the

power sensor or the ac connections, it will be necessary to remove the
front panel of the Cal Cart.

1. Remove both screws on the front panel, between the RF connector and the

handle.

2. Pull on the handle set into the base of the front panel to remove it.

Note:

When making AC connections, refer to the following wiring

diagram.

Figure 17 Cal Cart Wiring Schematic

WARNING

To avoid personal injury, disconnect the power cord from the AC line before

performing any maintenance, including fuse replacement or changing the

line voltage setting.

Содержание Thruline 4020 Series




























































Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды

Bird Electronic Thruline 4020 Series, Инструкция

Результаты поиска

Содержание Thruline 4020 Series

Отзывы:

Похожие инструкции для Thruline 4020 Series

Бренды по названию

Популярные бренды