background image

PSU ERROR CODE AND SOLUTION

Error
code

Description

Possible cause

Solution

E001

PSU

Over

current

Input voltage too low

Check the mains voltage, and make sure
correct and firm connection

E002

Working current changes too fast

Slower regulation control

E003

Rapid changes on the load or problem with
the loads

Check ozone cell and HV transformer

E004

PSU

over

voltage

Input voltage abnormal

Check the mains voltage, and make sure
correct and firm connection

E005

Working current changes too fast

Slower regulation control

E006

PSU output voltage increase too fast

Change settings on the parameters

E007

Rapid changes or problem with the loads

Check ozone cell and HV transformer

E008

Phase loss

PSU input R, S, T phase loss

Check the mains voltage, and make sure
correct and firm connection

E10

IGBT
protection

PSU Output short circuit
Load short circuit or abnormal
Cooling fan channel blocked or cooling fan
issue
Ambient temperature too high

Check PSU output cables
Check HV transformer and the connections
Clean the cooling channels, replace cooling
fan
Lower ambient temperature

E11

PSU

IGBT

over heated

Cooling fan channel blocked or cooling fan
issue
Ambient temperature too high

Clean the cooling channels, replace cooling
fan
Lower ambient temperature

E12

rectifier
modules over
heated

Cooling fan channel blocked or cooling fan
issue
Ambient temperature too high

Clean the cooling channels, replace cooling
fan
Lower ambient temperature

E13

PSU overload

PSU input voltage too low
PSU Over current

Check the mains voltage, and make sure
correct and firm connection
Decrease the current by setting to lower
ozone

Note

If the problem still exists after the above inspection, please contact our company or local distributor.

All maintenance/replacement can only be conducted when the power is off and pressure released,
ensuring the safety of the operation personnel.

When servicing a SOZ series ozone generator with multi-set individual control, make it clear of the
component in each set (AB set: breaker, contactor, relay, digital power supply unit, transformer,
ozone cell, cooling pipe, control panel).

15

Содержание AQUAZONE 200G


















Отзывы: