BIOTRONIK Evia HF Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 138

BIOTRONIK Evia HF Скачать руководство пользователя страница 32

Chapter 5

Programmable Parameters

Evia HF / HF-T Technical Manual

PAGE 24

Figure 8: Pulse Width

NOTE:

When VCC is programmed to ON or ATM, the pulse width cannot be programmed to a value higher

than 0.4 ms.

5.4 Automatic Sensitivity Control (ASC)

Chamber

Range

Default

Atrium

Auto, 0.1...(0.l)...1.5...

(0.5)...7.5 mV

Auto

Right Ventricle

Auto, 0.5...(0.5)...

7.5 mV

Auto

Left Ventricle

OFF, Auto, 0.5...

(0.5)...7.5 mV

Auto

The parameter “sensitivity” is used to set the pulse generator’s threshold for detecting intracardiac

signals. The lower the programmed sensitivity value, the higher the device’s sensitivity.
If intracardiac signals are of low amplitude, a change to a higher sensitivity (lower value) may be

necessary. Conversely, if the sensing amplifier is responding to extraneous signals, such as artifact

or interference, a change to a lower sensitivity (higher value) may resolve the difficulty. In dual-

chamber sensing modes, the sensitivity values for the atrial and ventricular channels are independently

programmable.
With unipolar sensing, the lowest sensitivity setting is 0.5 mV in the atrium. Blue conflict icons for the

atrial channel shown in

show a conflict message, requiring the user to program the lead to a

bipolar configuration before the value can be permanently programmed.
A conflict will appear when attempting to program 0.5 mV in the ventricle, as shown in

, with

unipolar sensing. The user is asked to extend the Ventricular Blanking after Ap to resolve the conflict.

This is done to reduce the potential of oversensing the atrial pacing spike with unipolar sensing. Once

resolved, the user can program 0.5 mV sensitivity in the ventricle.
If a sensing test has been performed, the sensing value is displayed at the bottom of the sensitivity

parameter to guide sensing programming of the device.

«
...
30
31
32
33
34
...
»

Содержание Evia HF











































































































































Отзывы:

Нет отзывов