BIOTRONIK Evia HF Скачать руководство пользователя страница 115

Страница: 115 / 138

Chapter 10

Follow-up Procedures

Evia HF / HF-T Technical Manual

PAGE 107

Programmed Stimulation Screen

10.6.4 Back up Pacing

The back up pacing program remains active once NIPS has been selected and remains active during

burst or programmed burst stimulation and within this menu. This program remains active until the

Stop

touch key is pressed.

CAUTION

Short Pacing Intervals –

Use of short pacing intervals (high pacing

rates) with long atrial and/or ventricular refractory periods may

result in intermittent asynchronous pacing and, therefore, may be

contraindicated in some patients.

10.6.5 NIPS Safety Features

The BIOTRONIK offers the following safety features during NIPS sessions.

• When the battery voltage has reached the Elective Replacement Indicator point (ERI), the NIPS

feature is no longer available.

• Atrial pacing support is available to pacemaker dependent patients during burst or programmed

burst stimulation through the back up pacing program as long as the wand is within 15 cm of the

pulse generator. Removing the programmer wand or placement to distance greater than 15 cm

from the pulse generator returns the pulse generator to its permanent program.

• NIPS may only be programmed temporarily.

NOTE:

High pacing rates and pulse amplitudes together with wide pulse widths may temporarily decrease

the amplitude of the pacing pulse. The pacing pulse must be continuously verified with an ECG to

assure effectiveness.
To perform NIPS function, the programmer wand must be placed directly over the pulse generator to

enable continuous telemetry.

Содержание Evia HF











































































































































Результаты поиска

Содержание Evia HF

Отзывы:

BIOTRONIK Evia HF, Техническое руководство, Страница: 115 / 138

Результаты поиска

Содержание Evia HF

Отзывы: