BIOTRONIK Evia HF Скачать руководство пользователя страница 112

Страница: 112 / 138

Chapter 10

Follow-up Procedures

Evia HF / HF-T Technical Manual

PAGE 104

Figure 65: Retrograde Conduction Test with a Positive Result

Retrograde conduction from the ventricle to the atrium can be confirmed when a 1:1 relationship with

a constant V-A interval is present. The VA interval is the time between the ventricular paced event and

the first subsequent atrial sense.
The programmer displays the measured results as the maximum, minimum, and mean retrograde

conduction times. If the measured maximum, minimum and mean values are within 25 ms of each

other, retrograde conduction is suspected. One may repeat the test to confirm the results.
While the test is being performed, the measured V-A times are displayed on the programmer screen.

10.5.1 Measuring Retrograde Conduction

The Retrograde Conduction measurement is initiated from the Retrograde conduction tab. During

the test, the pacemaker operates in VDI mode at a programmable rate that must exceed the heart’s

intrinsic rate. The V-A interval is measured using the event markers on the IEGM (V pace to A sense).

The measurement begins after the START tab is pressed. The first five cycles are not used in the

measurement.

10.5.2 Requirements for Measurement

• The programming head must have telemetry contact with the implant for the entire measurement

duration. If telemetry contact is interrupted, the measuring process will be aborted. (This is true for

all tests.) The values measured up to this point remain displayed.

• Retrograde conduction can only be measured if ventricular pacing and atrial sensing

are present.

• The ventricular pacing rate for the retrograde conduction test MUST be greater than the intrinsic

atrial rate.

NOTE:

Retrograde conduction may not be present at all rates. If retrograde conduction is suspected, perform

the test at different rates.

Содержание Evia HF











































































































































Результаты поиска

Содержание Evia HF

Отзывы:

BIOTRONIK Evia HF, Техническое руководство, Страница: 112 / 138

Результаты поиска

Содержание Evia HF

Отзывы: