background image

K8VGA-M 

i

 

 

FCC Information and Copyright 

 

This equipment has been tested and found to comply with the limits of a Class 
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. There is no guarantee 
that interference will not occur in a particular installation. 

 

The vendor makes no representations or warranties with respect to the 
contents here and specially disclaims any implied warranties of merchantability 
or fitness for any purpose. Further the vendor reserves the right to revise this 
publication and to make changes to the contents here without obligation to 
notify any party beforehand. 

 

Duplication of this publication, in part or in whole, is not allowed without first 
obtaining the vendor’s approval in writing. 

 

The content of this user’s manual is subject to be changed without notice and 
we will not be responsible for any mistakes found in this user’s manual. All the 
brand and product names are trademarks of their respective companies. 

 
 
 
 
 
 
 
 
 
 

Содержание K8VGA-M






























Отзывы: