background image

 

 

USER MANUAL 

TD064-O&M-001 

REVISION 4  

 

 
 

Page 11 of 38 

 
 

 

 

 

3

 

HPV GENERATOR CONNECTION 

Note: The following instructions assume that the HPV Generator is 
located next to the chamber with a power outlet socket nearby. In other 
configurations the HPV Generator may be installed via fixed pipework in 
a technical space away from the chamber, or integrated into the 
chamber. 

Refer to the User Manual for the Generator with regard to loading Hydrogen 
Peroxide and setting up ready for operation. 

Connections to HPV Generator 

For HPV disinfection cycles, connections to the Generator can be via fixed 
installation pipework (if generator is to be located in a technical space away from 
the WIC) or by flexible hosing (as standard supplied with the Generator). 
Positioning of the WIC inlet / outlet connections will vary dependent upon Client 
requirements.  

 

 

 
For both fixed pipework and flexible 
hosing the connections to the 
Generator and WIC are Camlock 
connections. 
 
 
Camlock connector. 

The H

2

O

2

 return hose is fitted with a male Camlock connection to attach to the 

Generator and a female Camlock connection at the remote end to connect to the 
chamber. 

(Note: The colour coding of the hose and connector is blue). 

 

The H

2

0

2

 supply hose is fitted with a female Camlock connection to attach to the 

Generator and a male Camlock connection at the remote end to connect to the 
chamber.

 

(Note: This insulated hose goes to the red colour coded 

connection). 
 

The communication cable connection may be located in various positions on the 
chamber dependent upon Client requirements. 

 

There is a dedicated mains socket to power the HPV generator if the Generator is 
placed at the front of the WIC. If it is not located at the front then a dedicated 
power socket outlet must be within 2m of the HPV generator. 
 
 

Содержание WIC-1







































Отзывы:

Похожие инструкции для WIC-1