bintec elmeg H2 Auto Compact Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 40

bintec elmeg H2 Auto Compact Series Скачать руководство пользователя страница 7

Chapter 1 About this manual

This is the installation manual for the bintec H2 Auto Compact router. It contains instructions on how to install the
device in a working environment. It provides technical parameters and safety instructions.

1.1 Supported devices

The information in this manual only applies to the bintec H2 Auto Compact router.

1.2 Who should read this manual?

This manual should be read by support personnel who need to install, configure, maintain and monitor the device.

1.3 When should you read this manual?

Read this guide as soon as you are ready to familiarize yourself with the device and its components.

The information contained in this manual will help you operate your device and understand its capabilities.

1.4 What is in this manual?

This installation guide contains the following:

• A description of the features available on the bintec H2 Auto Compact router.

• A description of the technical specifications.

• A detailed description of the power supply requirements.

• A description of the LEDs and connectors on the device.

• Troubleshooting information.

1.5 What is not in this manual?

This manual does not contain information on the device's software and configuration. For information on how to con-
figure the device, please read the relevant protocol manuals found at http://www.bintec-elmeg.com.

1.6 How is the information organized?

Each chapter focuses on a specific hardware component or part thereof. All the information on a particular compon-
ent (such as its technical specification, description, etc.) can be found in its relevant section.

Note

Additional product documentation covering the latest software and hardware features can be accessed
here:

support.teldat.com

1.6.1 Safety instructions

To reduce the risk of personal injury and damage to property, this manual contains some safety instructions. They
are classified by symbols and signal words. Please read and follow them carefully.

To reduce the risk of personal injury, the following symbols and signal words are used:

bintec elmeg GmbH

1 About this manual

bintec H2 Auto Compact

1

«
...
5
6
7
8
9
...
»

Содержание H2 Auto Compact Series









































Отзывы:

Нет отзывов