manualshive.com logo in svg

bintec elmeg H2 Auto Compact Series, Руководство по установке, Страница: 30 / 40

Поделиться
Скачать
bintec elmeg H2 Auto Compact Series Скачать руководство пользователя страница 30

Appendix A Technical information

A.1 Troubleshooting

The following table lists common problems and potential solutions to help you when installing your router. Please
contact your dealer for further information if you are unable to solve a problem.

Problem

Solution

None of the LEDs on the router
lights up.

Check the power supply to the router (power supply cable, main power outlet).

The LAN LED do not light up.

Check the Ethernet cable and the network connection.

The Cell LED (WWAN modules)
remains OFF.

Check the SIM card has been inserted correctly,

or

Check you have entered the correct SIM PIN,

or

Check the antenna is properly installed (make sure it is screwed in correctly),

or

Check that the SIM tray configuration is correct.

A.2 Maintenance

Given that bintec H2 Auto Compact routers are designed to be highly available and durable, they have not moving
parts.

This design makes maintenance unnecessary.

A.2.1 Software updates

bintec H2 Auto Compact routers can be updated to newer versions. Please contact your dealer for information
about new versions.

Our routers can be updated in several ways. For further information , please see the following manual: bintec
Dm748-I Software Updating.

The software required to update one of our routers is supplied in a format known as distribution. It consists of a
single file that contains the complete set of files for updating your device plus in-depth information on the contents of
each file.

The bintec H2 Auto Compact incorporates independent modules for the Wireless WAN interface. The module firm-
ware is usually independent of the router's software. There is an UPGRADE file for each Wireless LAN module.
Please ask your dealer for the appropriate UPGRADE file (which will depend on the module in your device). The Cel-
lular Interface manual (bintec Dm 781-I) shows you how to UPGRADE the module.

A.2.2 Connecting to the device

There are two ways to access the CLI:

• Through the Conf connector.

• Through the Telnet protocol.

Technical information

bintec elmeg GmbH

24

bintec H2 Auto Compact

Содержание H2 Auto Compact Series









































Отзывы:

Нет отзывов