Binatone Latitude 250 Скачать руководство пользователя страница 1

Power charge socket (    ) 

& Headset socket (    )

- micro-USB socket for 

charging installed batteries

- 2.5mm headset socket

CHG

CHG

USER GUIDE 

Latitude 250

Antenna 

PTT(push to talk)

button  

-press and hold

to transmit.  

Power (   ) button 

-press and hold to

turn the PMR 

unit ON or OFF. 

MENU (    ) button 

-press to program 

the PMR settings. 

LCD screen 

-Displays the current 

Channel selection and 

other radio symbols. 

MIC(microphone) 

Speaker 

UP(   ) / DOWN(    ) buttons 

-press to change

channels, volume, and    

to select settings   

during programming. 

CALL (    )button 

-press to send a ringing 

tone to other PMR units. 

1. LCD Screen

Channel Number. Changes from 1 to 

8 as selected by the user. 
Indicates battery charge level

FM

Displays when Scan function is activated 

Displays with frequency when the FM radio is activated 
Displays when Key Lock function is activated 
Displays when transmitting a signal. 
Displays when receiving a signal. 
Indicates the speaker volume level 

Mon-Fri from 8.00am to 8.00pm

Sat from 8.30am to 2.00pm

0844 557 9677 (UK only - Calls cost 7p per minute plus 

your telephone company's access charge.) 

/ 0818 762092 ROI

 or send email to us: 

[email protected]    www.binatoneglobal.com

2. Installation

a. Pull the belt clip latch 

  away from the PMR. 

2.1  Removing the Belt clip 

b. While pulling the belt

  clip latch, push up 

  the belt clip as 

  shown in Fig. 1. 

a. Slide the belt clip into 

  the slot as shown 

 in 

Fig. 2.

b. A “click” indicates the

 belt clip is locked into 

  its position.

a. Unclip the battery compartment cover.

b. Insert the 3xAAA batteries. Position the batteries 

  according to the polarity marking 

  in the battery compartment. See Fig.3

c. Replace the battery cover. See Fig. 4.

2.2  Installing the Belt clip 

2.3  Installing the Batteries 

Notes: 

·
·

Use only same type and make of batteries on the PMR units.

·

The PMR units have a built-in Power Saver (PS) for maximum

battery life, but when not in use, turn the units OFF to save

battery power.

Figure 1 

Figure 2 

Remove the batteries if the units will not be used for a long period

of time.

Figure 3 

Figure 4 

Binatone Help Line - 0844 5579677

3. Operation

Insert the USB connector (5.0V DC/400mA)

mains adaptor into the power-in 

micro-USB socket in the side of 

the Radio unit. Plug the mains

USB adaptor into a suitable mains 

socket with the switch on the socket 

to Off, and then turn it On. 

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Use only AAA size Ni-MH, 1.2V, 600mAh rechargeable batteries.

Battery meter

2.4  Charging the batteries using Adapter

CAUTION!

Binatone Help Line - 0844 5579677

The Latitude 250 must be charged using the mains USB adaptor 

provided. Using any other USB adaptor will result in any non-compliance 

with EN60950-1 and will invalidate the approvals and warranty.

Note:

Important: Always turn Off 

the PMR units when 

charging. This will shorten 

the charging time.

Main socket

It takes about 10 hours to fully recharge the batteries if they

completely run down. New batteries take up to 14 hours to fully charge.

Do not mix battery types when using the PMR unit.

The PMR unit has a built-in power saver (PS) for maximum battery

life, but when not in use, turn the units Off to save the battery power.

Remove the batteries if the unit will not be used for a long period of time.

Dispose of used batteries safely at a recycling centre. NEVER put

them anywhere they could get burnt or punctured.

The battery icon is located in the left corner of the LCD panel. This battery icon indicates 

the battery level, and when it reaches its minimum level, the handset will emit two beep 

tones and then it will automatically turn Off the power.

Battery life

The PMR has a built in power saver feature to make the batteries last longer. But when 

you are not using the handset, it’s better to switch off to save the battery power.

a. Press and hold the     (Power) button. A special “beep” sound

  will be heard. The LCD screen will display the current channel. 

To Turn ON;

The talk range depends on the environment and terrain. It will reach 

up to about 5km in wide open spaces, without obstructions such as 

hills, buildings or trees.

Don't use two PMR units too close together otherwise you may get 

loud feedback interference.

a. Press and hold the     (Power) button. A single “beep”

 will 

be heard and LCD screen will turn blank. 

To Turn OFF;

3.1  Turning the Unit ON/OFF

The PMR has 8 available channels.

 To change channels, in 

normal mode;

a. Press the      (Menu) button, the channel icon “1” on the LCD 

screen will start blinking.

b. While the Channel icon is blinking, press the     or 

button to select the desired channel. The channel changes 

from 1 to 8, or vice versa.

c. Press the       (Menu) button to confirm your setting and return 

to the standby mode.

Binatone Help Line - 0844 5579677

3.2  Adjusting the speaker volume

There are 8 volume levels, the current speaker volume level

is displayed on the LCD screen.

To adjust the speaker volume level, press the   button to 

increase, or press the      button to decrease. The LCD screen will 

display the speaker volume icon bars ascending, or descending 

respectively.

3.3  Receiving a Call

The unit is continuously in receive mode when the unit is turned 

ON and not transmitting. When a signal is received on the current 

channel, the receive signal icon “RX” will be displayed on the 

LCD screen.

3.4  Transmitting (sending)

a. Press and hold the 

PTT

 button to transmit your voice. The    

transmit signal icon “TX” will display on the LCD screen.

b. Hold the unit in a vertical position with the Mic (Microphone) 

5 cm away from the mouth. While holding the 

PTT

 button, 

speak into the microphone in a normal tone of voice.

c. Release the 

PTT

 button when you want to finish transmitting. 

3.6  Changing Channels

3.5  Roger Beep

The Roger beep is a tone which is automatically transmitted 

whenever the 

PTT

 button is released. This alerts the receiving 

party that you have ended the transmission.

Binatone Help Line - 0844 5579677

You can use the Monitor feature to check for weaker signals in the 

current channel.   

To activate this feature: 

3.7  Calling (Paging) Tone

a. With the PMR in normal mode, press and release the

 button. The unit will transmit a 2-second page tone to any other

 unit/s set with the same channel within transmitting range

3.8  Channel Scan 

3.9  Monitor Feature 

Your radio can scan the 8 channels for any activity. This allows to 

find other radios without having to manually change the channel.  

To activate this feature: 

a. Press and hold the       and      button at the same time and

channel scanning will start immediately, with SC displayed on the

screen and the channel number cycling through the channels.

When a signal is detected, the unit will pause on that channel, while

receiving the signal and for a further 3 seconds.

b. Press the         button to stop scanning and talk on that channel,

or press the     or     button to manually restart the scanning. 

PTT

c. To stop scanning, press the      button and return to standby mode. 

a. Press and hold the     and     button at the same time. The 

receiving icon “RX” appears on the display, and the speaker 

turns on and plays any signals on the current channel. 

b. Press the      button to stop the monitoring. 

3.10 To Lock the Buttons 

FM Radio function 

With the buttons lock you can still transmit (TX), or call the current 

channel, but you can not change the volume. To activate this 

feature;   

In the standby mode, press and hold the      until the   

icon appears on the LCD screen. 

To unlock the buttons 

Press and hold again the      button until the        icon 

disappears on the LCD screen.   

3.11

You can use the CALL button to send a tone to other users on 

the same channel. To activate this feature; 

While in standby mode, press and release the power button. The FM

Frequency will display in the LCD screen. Press the Up or Down 

button to adjust the FM frequency channel.

You can still transmit (TX) and receive (RX) calls on your current 

channel, with the FM radio being interrupted during calls.

Press and release the Power button to go back to PMR frequency 

mode.  

Отзывы: