manualshive.com logo in svg

bihl+Wiedemann AS-Interface 2.1, Руководство пользователя

Поделиться
Скачать
bihl+Wiedemann AS-Interface 2.1 Скачать руководство пользователя страница 13

                           

   

         

AS-Interface Analog Module 

General Information

Subject to reasonable modifications due to technical advances

Copyright Bihl+Wiedemann, Printed in Germany

Bihl+Wiedemann GmbH  ·  D-68199 Mannheim  ·  Phone +49-621-339960  ·  Fax +49-621-3392239  ·  Internet http://www.bihl-wiedemann.de

is

sue da

te

 20

.1

.2

0

0

4

13

3.4

Analog Modules with 4 Channels in Protection Category IP20

The range consists of 5 AS-Interface analog modules: 2 modules with 4 analog in-
puts 0 - 10 V or 4 - 20 mA respectively, 2 modules with 4 analog outputs 0 - 10 V 
or 0 - 20 mA respectively and a module 4 Pt100 inputs.

3.4.1

Analog Modules with 4 Inputs

The analog module has 4 analog inputs.
The connection of sensors is made by Combicon clamps. The sensors can be sup-
plied by AS-Interface or external help voltage (according to PELV). The current 
supply switches automatically to external help voltage, as soon as this is set up.

The sensors and AS-Interface are galvanical seperated.

The conversion of the measured value and the data transmission via AS-Interface 
occurs asynchronically according to AS-Interface Profile 7.3.
The resolution of the analog data is 16 Bit. The analog modules contains 50 Hz 
and 60 Hz filters. These filters can be optionally switched with the help of the 
AS-Interface parameters.

3.4.2

Analog Modules with 4 Outputs

The analog module has 4 analog outputs.
The connection of actutators is made by Combicon clamps. The actutators can be 
supplied by AS-Interface or external help voltage (according to PELV). The current 
supply switches automatically to external help voltage, as soon as this is set up.

The actutators and AS-Interface are galvanical seperated.

The conversion of the measured value and the data transmission via AS-Interface 
occurs asynchronically according to AS-Interface Profile 7.3. The resolution of the 
analog data is 16 Bit. 

3.4.3

Analog Module with 4 Pt100 Inputs

The analog module has got 4 Pt100 inputs.
The connection of actutators is made by Combicon clamps. 

The sensors and 

AS-Interface are galvanical seperated

. The commission of the measured value 

and the data transmission via AS-Interface occurs asynchronically according to 
AS-Interface Profile 7.3. 
The resolution of the analog data is 16 Bit. The analog modules contains 50 Hz 
and 60 Hz filters. These filters can be optionally activated with the help of the 
AS-Interface parameters.

3.5

Analog Modules with 4 Channels, M12 Connection in Protection 
Category IP65

The range consists of 5 AS-Interface analog modules: 2 modules with 4 analog in-
puts 0 - 10 V or 4 - 20 mA respectively, 2 modules with 4 analog outputs 0 - 10 V 
or 0 - 20 mA respectively and a module 4 Pt100 inputs.

Содержание AS-Interface 2.1







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды