Bigdog Mower Co. Alpha Скачать руководство пользователя страница 22

REV A

3-6

607233

Operating Suggestions      

Inexperienced operators may have a tendency to oversteer 

and lose control. Practice slow maneuvers at low engine rpm

 

(idle) on a flat open area before attempting normal speed 
operation.

 

When turning on soft wet turf, keep both wheels rolling 

either forward or backward. Pivoting on one stopped wheel 
can damage turf, especially when mowing.

Set the throttle at full rpm for maximum performance. This 

gives maximum power to the drive wheels and deck when 
needed. The throttle setting directly controls blade speed. 
Use the control levers to control ground speed rather than 
engine rpm. 

Keep blades sharp.

 

Many problems

 with incorrect cutting 

patterns are 

due to dull blades

 or blades which have been 

sharpened incorrectly.

 Information on sharpening blades is 

listed in this manual’s maintenance section. 

Blade sharpness 

should be checked daily. 

   

Direct grass discharge to the right,

 away from the 

unmowed area. Generally, this means using a pattern of 

left 

turns.

 Avoid throwing grass discharge onto unmowed area. 

Mowing clippings puts an unnecessary load on the unit and 
reduces mowing efficiency.

When mowing a lawn for the first time

 cut grass slightly 

longer than normal to avoid scalping uneven terrain. When 
cutting grass taller than six inches, you may want to mow the 
lawn twice to achieve a better quality of cut.

During normal mowing cut only about 1/3 of the grass 

blade.

Alternate the mowing direction 

to keep the grass growing 

straight and for better dispersion of the clippings.

Remember, grass grows at different rates 

at different 

times of the year. Mow more often in the early spring to 
maintain the same cutting height. As the growth rate slows 
in midsummer, mow less frequently. If you cannot mow at a 
regular interval, mow at a high cutting height; then mow

 

again two days later at a lower cutting height.

Raise the cutting height of the mower 

if the cutting width 

of the mower is wider than the previous mower. This ensures 
that uneven turf is not cut too short.

Raise the cutting height of the mower 

if the grass is 

slightly taller than normal or if it contains a high degree of 
moisture. Then mow it again with the cutting height set 
lower.

If the machine’s forward motion

 must be stopped while 

mowing, a clump of grass clippings may drop onto your lawn. 
To avoid this, move onto a previously cut area with the 
blades engaged.

 

An inexperienced operator should not mow on 
slopes or on uneven terrain.
Before attempting normal speed operation an 
inexperienced operator should: 

be thoroughly familiar with the proper use 
and operation of the equipment.

read the manual completely and thoroughly.

have attempted slow moving maneuvers.

If you lose steering control while operating the 
machine, place the steering control levers in the park 
brake position immediately. Inspect the machine and 
involve your BigDog

®

 Mower Dealer to resolve the 

problem before continuing to operate.

The unit’s steering control levers are very 
responsive: Easy does it! For smooth operation, 
move the levers slowly, avoiding sudden 
movement. Skill and ease of operation come with 
practice and experience.   The machine can spin 
very rapidly. Use caution when making turns and 
slow down before making sharp turns.

Sharp depressions or raised obstacles (such as 
gutters or curbs) should not be directly 
approached at high speed in an attempt to “jump” 
them as the operator could be thrown from the 
equipment. Approach at a slow speed and angle 
one drive wheel at the obstruction. Continue at an 
angle until the wheel clears and then pivot the 
opposite wheel around.

DANGER

WARNI

N

G

WARNING

WARNING

Never work with blades while the engine is running 
or deck clutch switch is engaged (on). 
Always place the deck clutch switch in the 
disengaged position, place steering control levers 
in the park brake position, turn the engine off and 
disconnect the negative battery cable. 
Block the mower up when you must work under it. 
Wear gloves when handling blades. 
Always check for blade damage if the mower 
strikes a rock, branch or other foreign object 
during mowing!

Never direct the discharge of material from the 
mower deck toward bystanders. 

Never operate the mower deck with the 
discharge chute damaged, altered, removed, 
or in the raised position, except when the 
entire grass catcher attachment or mulching 
system is being used. Figure 3-9

DANGE

R

WARNI

N

G

Содержание Alpha








































Отзывы: