background image

31

Installation, Operation and Maintenance Manual

MAN 607 Rev. 6

February 2022

Section 5: Maintenance

Maintenance

Standard temperature conditions (-30 °C/+85 °C):

Producer

AGIP

Name

ARNICA 22

Viscosity at 40 °C

20.9 mm²/s

Viscosity at 100 °C

4.73 mm²/s

Viscosity index ASTM

153

Flash point

192 °C

Pour point

-42 °C

Specific weight (at 15 °C)

0,857 kg/l

Equivalent oils:

SHELL TELLUS PLUS 22
CHEVRON HYDRAULIC OIL AW ISO 22
MOBIL DTE22
EXXON UNIVIS N22
EQUIVIS ZS22

BP ENERGOL HLP-HM22

CASTROL DYSPIN AWS22

Low temperature conditions (until -46 °C):

Manufactured 

SHELL

Name

AEROSHELL FLUID 41

Viscosity at -54 °C

2300 cST 

Viscosity at -40 °C

491 cST

Viscosity at 40 °C

14,1 cST

Viscosity at 100 °C

5,30 cST

Viscosity index (ISO 2909)

>200

Flash point

105 °C

Pour point

<-60 °C 

Specific weight (or equivalent)

0,87 kg/dm

3

Low temperature conditions (until -60 °C):

Manufactured 

SYNTESIS

Name

SYNTRASS-CS 500

Viscosity at -60 °C

580 cST

Viscosity at -30 °C

39 cST

Viscosity at 20 °C

5,8 cST

Viscosity at 50 °C

2,1 cST

Flash point

152 °C

Pour point

-68 °C

Specific weight (or equivalent)

0,897 kg/dm

3

NOTICE

For refill, use oil of the same brand as previous, refer to related technical documentation.

Table 10.  

Features of hydraulic oil suggested by Biffi Italia s.r.l. for refilling

                               in different working conditions

Содержание OLGA-H



























































Отзывы: