background image

Page 1 
 

bhi 

 

Copyright & Disclaimer

Copyright: This publication, including all photographs and illustrations is protected under 
international copyright laws, with all rights reserved. Neither this manual, nor any of the material 
within, may be copied or reproduced without the written consent of bhi Ltd.  
Disclaimer:  The information in this document is subject to change without notice. bhi Ltd. makes no 
representations or warranties with respect to the contents hereof and specifically disclaims any 
implied warranties of merchantability or fitness for any particular purpose. Furthermore, bhi Ltd. 
reserves the right to revise this publication and to make changes from time to time in the content 
hereof without obligation of bhi Ltd. to notify any person of such revision or changes.

 

 

1.

 

Introduction 

 The NEDSP1901-PCB module is designed to take line level audio signals and 

the NEDSP1901-PCB-MIC version is designed for use with various microphones. They are 
separate products and need to be ordered separately, and they are not interchangeable, 
although the NEDSP1901-PCB-MIC can also be used with line level audio signals.  
 
Note:  Go to page 12 for the specific NEDSP1901-PCB-MIC information 

 

NEDSP1901-PCB Version: 
 

The 

NEDSP1901-PCB

 module is an audio DSP noise cancelling module that is used to clean up noisy 

speech signals to give improved speech clarity in noisy conditions.  The 1901 module is pin for pin 
replacement module for the discontinued NEDSP1061-PCB

 

module.  It operates with a similar 

specification but incorporates the latest bhi DSP noise cancelling technology and maintains virtually 
the same physical dimensions as the NEDSP1061-PCB. 
 
 
         
 
 
 
 
 
 
 
 
 
                                   

DSP side of PCB  

 

 

                Rear side of PCB 

 

1.1

 

NEDSP 1901 Module Features: 

 

Fully adaptive to changing noise environments 

 

Input and output level controls 

 

Virtually no distortion to speech signals 

 

Up to 40 dB noise reduction in 8 selectable levels 

 

Audio bandwidth 300Hz to 5KHz 

 

Noise Reduction may be preset or remotely set during operation. 

 

7 to 18 Volt supply range 

 

Approximately 10 dB of signal gain with the ability to drive impedances of less than 1KOhm. 

 

Wide range of connection possibilities 

 

Mounting holes  

NEDSP1901-PCB User Manual Iss A 

NEDSP1901-PCB-MIC User Manual Iss A 

 

www.bhi-ltd.com

 

Содержание NEDSP1901-PCB


















Отзывы: