D812939 00096_03
40
- VIRGO SMART BT A
INSTALLATION MANUAL
ACCESS MENUS Fig. 2
x 2
Exit Menù
Confirm/Switch on display
Scroll up
Scroll down
stat
password
- +
- +
OK
vers
bft . . .
+
/
-
OK
0000
+
/
-
+
/
-
n. cycles
OK
OK
01.33
0---
10--
150-
1520
prg
00
- +
err
autoset
02.01
........
30.15
+
/
-
See PARAMETERS MENU
See LOGIC MENU
See RADIO MENU
add. start
hidden butt
hidden butt
release
release
desired button
desired button
Add. 2ch
erase 64
language
n. remotes
List of last 30 errors
Control unit
software version
No total
manoeuvres(in hundreds)
No radio control
devices memorised
0---
10--
150-
1520
ok
*** Password entry.
Request with Protection Level
logic set to 1, 2, 3, 4
***
Diagnostics
code
DESCRIPTION
NOTES
STRE
START E external start input activated
STRI
START I internal start input activated
OPEN
OPEN input activated
CLS
CLOSE input activated
PED
PED pedestrian input activated
TIME
TIMER input activated
STOP
STOP input activated
PHOT
Activation of PHOT photocell input or, if configured
as verified photocell, Activation of the associated
FAULT input
PHOP
Activation of PHOT OP opening photocell input or,
if configured as active verified photocell only when
opening, Activation of the associated FAULT input
PHCL
Activation of PHOT CL closing photocell input or, if
configured as active verified photocell only when
closing, Activation of the associated FAULT input
BAR
Activation of BAR safety edge input or, if configured
as verified safety edge, Activation of the associated
FAULT input
baro
Activation of BAR safety edge input with ACTIVE reversal
ONLY WHILE OPENING, or, if configured as verified safety
edge active only while opening, Activation of the asso-
ciated FAULT input
barc
Activation of BAR safety edge input with ACTIVE reversal
ONLY WHILE CLOSING, or, if configured as verified safety
edge active only while closing, Activation of the associated
FAULT input
SET
The board is standing by to perform a complete open-
ing-closing cycle uninterrupted by intermediate stops
in order to acquire the torque required for movement.
WARNING! Obstacle detection not active
ER01
Photocell test failed
Check photocell connection and/or logic settings
ER02
Safety edge test failed
Check safety edge connection and/or logic settings
ER03
Opening photocell test failed
Check photocell connection and/or parameter/logic setting
ER04
Closing photocell test failed
Check photocell connection and/or parameter/logic setting
er06
8k2 safety edge test failed
Check safety edge connection and/or parameter/logic settings
ER07
Opening safety edge test failed
Check safety edge connection and/or parameter/logic settings
ER08
Closing safety edge test failed
Check safety edge connection and/or parameter/logic settings
ER1x
*
Board hardware test error
- Check connections to motor
- Hardware problems with board (contact technical assistance)
ER2x
*
Encoder error
- Motor power or encoder signal cables inverted/disconnected.
- Actuator movement is too slow or stopped with respect to programmed
operation.
ER3x
*
Reverse due to obstacle - Amperostop
Check fo r obstacles in path
ER4x
*
Thermal cutout
Allow automated device to cool
ER5x
*
Communication error with remote devices
Check connection with serial-connected accessory devices and/or
expansion boards
ER70, ER71
ER74, ER75
Internal system supervision control error.
Try switching the board off and back on again. If the problem persists,
contact the technical assistance department.
ER72
Consistency error of the control unit’s parameters
(Logics and Parameters)
Pressing OK the detected settings are confirmed. The board will keep on
working with the detected settings.
The board settings must be checked
(Parameters and Logics)
ER73
D-track parameter error
Pressing OK, the board will keep on working with D-track as a default.
An autoset is required
Ersw
Error during limit switch adjustment
Only for
LUX BT E - LUX G BT
- Repeat the limit switch adjustment procedure.
- Try moving the maximum limits of both the opening and closing limit
switches.
- Caution: the last centimetre of the piston’s stroke, during either opening or
closing, cannot be used.
ERf3
Error in setting the SAFE inputs
Check the setting of the SAFE inputs is correct
*
X
= 0, 1, .., 9, A, B, C, D, E, F
Instantaneous force motor 2
Instantaneous force motor 1
35.40
C
=
SWC2 motor 2 closing limit
switch input activated
O
=
SWO1 motor 1 opening limit
switch input activated
C
=
SWC1 motor 1 closing limit
switch input activated
O
=
SWO2 motor 2 opening limit
switch input activated
