ENGLISH
INSTALLATION MANUAL
- Zone (
zone
) [ 0 ]
Set the zone number between a minimum value of 0 and a maximum value
of 127. See paragraph 8 on “Serial connection”.
6.2) LOGICS MENU
- TCA (
TCA
) [ OFF ]
ON: Activates automatic closing
OFF: Excludes automatic closing
- 3 Steps (
3 step
) [ OFF ]
ON: Enables 3-step logic. A start impulse has the following effects:
door closed: ............................................................................................................ opens
on opening: ................................................stops and enters TCA (if configured)
door open: ...............................................................................................................closes
on closing: ................................................................stops and reverses movement
after stopping: ....................................................................................................... opens
OFF: Disables 3-step logic.
- Impulse lock (
ibl open
) [ OFF ]
ON: Enables impulse lock during the opening phase.
OFF: Excludes impulse lock during the opening phase.
- Pre alarm (
pre-alarm
) [ OFF ]
ON: The blinker comes on about 3 seconds before the motor starts.
OFF: The blinker comes on at the same time as the motor starts.
- Rapid closing (
fast cls.
) [ OFF ]
ON: Closes the gate after photocell disengagement, before waiting for the end
of the TCA (automatic closing time) set.
OFF: Command not entered.
- Photocells on opening (
photoc. open
) [ OFF ]
ON: In case of obscuring, this excludes photocell operation on opening.
During the closing phase, it immediately reverses the motion.
OFF: In case of obscuring, the photocells are active both on opening and on clos-
ing. When a photocell is obscured on closing, it reverses the motion only
after the photocell is disengaged.
- Gate-open or 2nd radio channel warning light (
sca 2ch
) [ OFF ]
ON: The output between terminals 15 and 16s configured as gate-open warning
light, in this case the 2nd radio channel controls pedestrian opening.
OFF: The output between terminals 15 and 16 is configured as 2nd radio channel.
- Motors in operation (
1 mot. ON
) [ OFF ]
ON: Only motor 2 is in operation (terminals 7, 8 and 9).
With this configuration, the pedestrian input is disabled.
OFF: Both motors are in operation.
- Ram blow on opening (
ram blow c. op
) [OFF]
ON: Before opening, the gate is pushed for about 2 seconds in the closing di-
rection. This allows the electric lock to be released more easily (not affected
by limit switches).
OFF: Excludes the ram blow.
IMPORTANT –
When no adequate mechanical backstops are fitted, do not
use this function.
- Fixed code (
fixed code
) [ OFF ]
ON: The receiver is configured for operation in fixed-code mode, see paragraph
on “Radio Transmitter Cloning”.
OFF: The receiver is configured for operation in rolling-code mode, see paragraph
on “Radio Transmitter Cloning”.
- Radio transmitter programming (
radio prog
) [ ON ]
ON: This enables transmitter storage via radio:
1 - First press the hidden key (P1) and then the normal key (T1, T2, T3 or
T4) of a transmitter already memorised in standard mode by means of the
radio menu.
2 - Within 10s press the hidden key (P1) and the normal key (T1, T2, T3 or
T4) of a transmitter to be memorised.
The receiver exits the programming mode after 10s, other new transmitters
can be entered before the end of this time.
This mode does not require access to the control panel.
OFF: This disables transmitter storage via radio.
The transmitters can only be memorised using the appropriate Radio menu.
- Master/Slave (
Master
) [ OFF ]
ON: The control panel is set as Master in a centralised connection (see Paragraph
8).
OFF: The control panel is set as Slave in a centralised connection (see Paragraph
8).
- Start-Open
selection (
start-open
) [ OFF ]
ON: The input between the two terminals 17-20 acts as open.
OFF: The input between the two terminals 17-20 acts as start.
- PED-CLOSE selection (
ped-close
) [ OFF ]
ON: The input between the two terminals 17-21 works as CLOSE.
OFF: The input between the two terminals 17-21 works as PEDESTRIAN.
6.3) Radio Menu (
radio
)
- Add (
add
)
Allows you to add one key of a radio control device to the receiver memory;
after storage it displays a message showing the transmitter number in the
memory location (from 01 to 64).
NOTE:
When using transmitters with two or more channels, the first push-
button which has been stored is associated to the START function. If a second
push-button is stored, it will be associated to the pedestrian function.
- Read (
read
)
Checks one key of a receiver; if stored it displays a message showing the receiver
number in the memory location (from 01 to 64), and the key number (T1, T2,
T3 or T4).
- Delete (
erase 1
)
Removes one single key of a transmitter from the receiver memory; after
deletion it displays a message showing the receiver number in the memory
location (from 01 to 64).
- Eliminate list (
erase 64
)
WARNING!
Completely removes all memorised radio control devices from the
receiver memory.
6.4) Language Menu (
Language
)
Allows you to set the language on the display programmer.
5 languages are available:
- ITALIAN (
itA
)
- FRENCH (
FRA
)
- GERMAN (
DEU
)
- ENGLISH (
ENG
)
- SPANISH (
ESP
)
6.5) MENU DEFAULT (
DEFAULT
)
Restores the preset default values on the control unit.
6.6) DIAGNOSTICS AND MONITORING
The display on the
ALTAIR-P
panel shows some useful information, both during
normal operation and in the case of malfunctions.
Diagnostics:
In the case of malfunctions, the display shows a message indicating which device
needs to be checked:
STRT
= START input activation
STOP
= STOP input activation
PHOT
= PHOT input activation
PED
= input activation PEDESTRIAN
OPEN
= OPEN input activation
CLS
= CLOSE input activation
7) RADIO TECHNICAL SPECIFICATIONS
Receiver output channels:
- output channel 1, if activated, controls a START command.
- output channel 2, if activated, controls the excitation of the 2nd radio channel
relay for 1s, or activates the pedestrian function, depending on the setting.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with
.
7.1) ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG58 coaxial cable.
The presence of metallic masses next to the antenna can interfere with radio
reception. In case of insufficient transmitter range, move the antenna to a more
suitable position.
7.2) RECEIVER CONFIGURATION
Cloning operations can be carried out with the special universal palmtop
programmer only.
The on-board receiver combines characteristics of utmost
safety in copying variable code (rolling code) coding with the convenience of
carrying out transmitter “cloning” operations thanks to an exclusive system.
Cloning a transmitter means creating a transmitter which can be automatically
included within the list of the transmitters memorised in the receiver, either as
an addition or as a replacement of a particular transmitter.
Cloning by replacement is used to create a new transmitter which takes the place
of the one previously memorised in the receiver; in this way a specific transmitter
can be removed from the memory and will no longer be usable.
Therefore it will be possible to remotely program a large number of additional
transmitters or, for example, replacement transmitters for those which have been
lost, without making changes directly to the receiver.
When coding safety is not a decisive factor, the on-board receiver allows you to
carry out fixed-code additional cloning which, although abandoning the variable
code, provides a high number of coding combinations, therefore keeping it pos-
sible to “copy” any transmitter which has already been programmed .
7.3) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means of the
universal palmtop programmer which allows you to create installations in the
ALTAIR-P -
15
D811506_04
