BFit BFITW 1000 Скачать руководство пользователя страница 27

Страница: 27 / 76

VII

. Venting

(continued)

4 Pipe Diameters min.

12 in. min.

Above Snow Line

Grade/Snow Line

Bird Screen

Vent & Intake

Vent

Combustion

Air

Figure 6: Horizontal Sidewall Termination

12 in. Min.

Above Snow Line

24 in. Min.

From Intake

6 Pipe Diameters Min.

Bird Screen

Vent & Intake

Vent

Combustion

Air

Figure 7: Slopped Roof Termination

24 in. Min.

Above Intake

12 in. Min.

Above Roof/Snow Line

24 in. Min.

From Parapet

6 Pipe Diameters Min.

Above Parapet

24 in. Min.

From Parapet

Bird Screen

Vent & Intake

Figure 8: Flat Roof Vent Terminations

CAUTION

nstalling multiple vent terminations too close together may result in combustion product water vapor conden

sation on building surfaces where vent terminations are placed, causing subsequent frost damage. To avoid/

minimize frost damage, extend the distance from building surfaces to vent termination end and increase the

horizontal distance between adjacent vent terminations

Notes:

All terminations must have bird/rodent screens.

2. If Possible, Install Sidewall venting on a wall away from prevailing wind.

For roof terminations, install vent terminal downstream of prevailing winds relative to intake terminal.

It is recommended to use tee terminations with a vertical run in extra windy areas.

NOTICE

The required spacing between vent

and combustion air terminals is

to prevent flue gas recirculation.

Recirculation of flue gas products

into the combustion air supply can

cause damage to property or the

appliance.

Содержание BFITW 1000













































































Результаты поиска

Содержание BFITW 1000

Отзывы:

Бренды по названию

Популярные бренды

BFit BFITW 1000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BFITW 1000

Отзывы:

Бренды по названию

Популярные бренды