Beta Max MAXIAL TRACK HOIST Скачать руководство пользователя страница 94

Страница: 94 / 160

Use and Maintenance Instruction Manual

MAXIAL TRACK HOIST

REV. 2.2 (2017)

MAINTENANCE AND REPAIR

Page | 10-3

10.2.1 General maintenance (Daily)

Perform the maintenance described below daily:

—

check the work area near and around the hoist and hoistway is free from obstructions,
clutter, and trip hazards

—

confirm the power source has not changed

—

check that the power cord extensions are properly plugged into the power source

—

check that the Control/Electrical Box is properly connected to the Motor Pack

—

check that the Handheld Control Pendant is properly connected to the Control/Electrical
Box

—

confirm the top and bottom motor pack flip retainer locks are locked in place securing
the Motor Pack to the ladder track section

—

check to make sure the pins securing the Carrier Basket to the Universal Carriage are
inserted completely and contain safety pin locks

—

confirm the Sliding Head is locked in place secured to the Ladder Track section no
higher than the last Scaff-clamp

—

check that all guide rollers are present on the Universal Carriage

—

visually inspect all guide rollers on the Universal Carriage to notice any uneven wear
which may indicate the Universal Carriage is not tracking properly on the Ladder Track
and ensure the rollers move freely

—

check that all springs are in place on the Emergency Brake on the Universal Carriage

—

check that all springs are in place on the Slack Rope Assembly on the Motor Pack

—

run the system up to the top and back down visually inspecting the wire rope for any
kinks, birdcages, or breakage.

Wire rope should be replaced if damage is found.

—

Check that the wire rope is spooling properly and the wire rope will evenly reeve on the
drum

—

ensure the STOP pushbutton on the Handheld Control Pendant shuts off the system if
pressed

—

ensure the system shuts off the UP direction when the Universal Carriage reaches the
Top Stop

—

ensure the system shuts off the DOWN direction when the Universal Carriage reaches
the ground or Bottom Stop

—

ensure the system lifts, stops, and holds a full rated load

The General Maintenance (Daily) checklist form is located in appendix E of this manual.

Содержание MAXIAL TRACK HOIST

































































































































































Результаты поиска

Содержание MAXIAL TRACK HOIST

Отзывы:

Бренды по названию

Популярные бренды

Beta Max MAXIAL TRACK HOIST, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание MAXIAL TRACK HOIST

Отзывы:

Бренды по названию

Популярные бренды