background image

PROPER MAINTENANCE OF YOUR AUTOMATIC POOL CLEANER

CAUTION! REMOVE THE LADDER FROM THE POOL BEFORE STARTING.

Once your 

Automatic Pool Cleaner

 is connected to the pool, turn on your pump. The Automatic Pool Cleaner starts to clean the bottom of your 

pool. It will operate automatically until the filter basket is full. The filter basket has a removable mess bag designed to filter the sand and small 

particles from the bottom of the pool.

IMPORTANT!

 Make sure the mesh bag is in place during cleaner operation.

Empty this mesh bag regularly to ensure maximum suction. If your pool has many leaves or large debris on the bottom, they must be removed 

using a leaf skimmer (not included). This will prevent the basket from becoming full too quickly and allow the smaller particles to be collected.

HOW TO CLEAN

(1) See ”a” from the picture A. Press in the center to open the bottom cover.

(2) See ”b” from the picture B. Take out the filter plant.

(3) See “c” from the picture C. Separate the filter net ”c” and the filter frame ”c1”, then clean the filter plant.

ATTENTION: 

The velcro can stick to the back net and filter net inside. Please separate them properly to avoid any damage on the filter net.

HOW TO REPLACE THE DIAPHRAGM

(1) Open the bottom cover and take out the filter net.

(2) See from the picture A. Pull out the diaphragm assembly part from the product.

(3) See from the picture B. Separate the diaphragm ”a” from the connection tube, and take out the diaphragm O ring.

(4) Put on the new diaphragm with the ring, and connect them back to the tube according to the picture C.

(5) Insert the diaphragm assembly part in the original position, see the “b” from the picture D. Twist the diaphragm until it is in the vertical position.

(6) Put on the filter and cover with the lid.

A

B

C

D

A

B

C

1. When the weight (Part D) is moved to the left of the hose, it helps lower the vac cleaner.

2. When the weight (Part D) is moved to the right of the hose, it helps raise the vac cleaner.

HOSE WEIGHT APPLICATION

Ideally, the bottom surface of the cleaner should rest flat on the pool bottom. First, assemble the hose weight on the first long white hose (A) from 

the cleaner. If the cleaner leans forward, move the hose weight along the long white hose towards the cleaner. If the cleaner leans backward, move 

the hose weight to the next long white hose. 

6

Содержание 58628E









Отзывы: