background image

85183-2  AN

50

SERVICE: 1-888 8BESTAR (1-888 823-7827)

1

Remove the mattress. 

2

Remove the slats.

3

Unscrew the facades 
(screws VR-215).

VR-215

4x

Important information to read before starting the disassembly.
Keep this information for future reference.

DISASSEMBLY

IMPACT OR CRUSHING HAZARD: if wall attachment screws are removed before 
removing lift cylinders and metal mattress frame, wall bed cabinet can suddenly fall, 
resulting in serious injury or death.

•  Only a professional or qualified person should disassemble or adjust a wall bed.
•  Improper disassembly of the wall bed may result in bed detaching from the wall resulting 
  in serious injury.
•  Wall bed must remain attached to wall for the following disassembly steps (1-9).
•  Qualified person must have the skills and tools necessary to locate wall studs, identify type 
  of wall structure (wood, metal, masonry or other) and install screws correctly to wall structure. 
  Skills and tools include electronic stud finder, drill motor and bits, screwdriver, and ability to 
  correctly use these tools.

WARNING

NOTICE

•  By removing the mattress, 
  the bed frame will rise quickly.
•  Have a helper hold the 
  frame down while removing 
 the 

mattress.

Содержание 85183-2

























































Отзывы: