BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 450

background image

SENSseries LB 480
BERTHOLD TECHNOLOGIES GmbH & Co. KG

1 – 81

Volume 1

5 Explosion Protection

1

5.11

FM Certificate

To verify the availability of the Approved product, please refer to

www.approvalguide.com

THIS CERTIFICATE MAY ONLY BE REPRODUCED IN ITS ENTIRETY AND WITHOUT CHANGE

FM Approvals LLC. 1151 Boston-Providence Turnpike, Norwood, MA 02062 USA
T: +1 (1) 781 762 4300 F: +1 (1) 781 762 9375 E-mail:

[email protected]

www.fmapprovals.com

F 347 (Mar 16)

Page 1 of 3

CERTIFICATE OF CONFORMITY

1.

HAZARDOUS (CLASSIFIED) LOCATION ELECTRICAL EQUIPMENT PER US REQUIREMENTS

2.

Certificate No:

FM16US0282X

3.

Equipment:
(Type Reference and Name)

LB 480 Series Scintillation Measurement Equipment

4.

Name of Listing Company:

Berthold Technologies GmbH & Co. KG

5.

Address of Listing Company:

Calmbacher Strasse 22
75323 Bad Wildbad
Germany

6.

The examination and test results are recorded in confidential report number:

3054263 dated 22

nd

September 2016

7.

FM Approvals LLC, certifies that the equipment described has been found to comply with the following Approval
standards and other documents:

FM Class 3600:2011, FM Class 3615:2006, FM Class 3616:2011,

FM Class 3810:2005, ANSI/NEMA 250:1991

8.

If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to specific
conditions of use specified in the schedule to this certificate.

9.

This certificate relates to the design, examination and testing of the products specified herein. The FM
Approvals surveillance audit program has further determined that the manufacturing processes and quality
control procedures in place are satisfactory to manufacture the product as examined, tested and Approved.

10. Equipment Ratings:

Explosionproof for Class I, Division 1, Groups A, B, C and D; Dust-ignitionproof for Class II, Division 1, Groups
E, F and G; and Class III, Division 1 hazardous (classified) locations, indoors and outdoors (Type 4X) with an
ambient temperature rating of -40°C to +65°C (or +80°C).

Certificate issued by:

22 September 2016

J. E. Marquedant
Manager, Electrical Systems

Date

«
...
79
80
81
82
83
...
»

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LB 480

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 63

Бренд: Hama Страницы: 6

Бренд: jenway Страницы: 50

Бренд: jenway Страницы: 62

Бренд: H-Star Страницы: 36

DGX Gears XTRA Regulator

Бренд: Dive Gear Express Страницы: 26

Бренд: A&D Страницы: 2

Бренд: Wacom Страницы: 23

Бренд: BART Страницы: 24

Бренд: Ozito Страницы: 8

Module NI PXI-8250

Бренд: National Instruments Страницы: 4

Бренд: Major tech Страницы: 28

Бренд: Diagtools Страницы: 18

Бренд: CPD GROUP Страницы: 3

SPECTRAMAGIC NX -

Бренд: Konica Minolta Страницы: 20

Phasing Ranger 2

Бренд: Bierer Страницы: 16

Бренд: Roland Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды