BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 437

Страница: 437 / 450

SENSseries LB 480 Level measurement
BERTHOLD TECHNOLOGIES GmbH & Co. KG

3 – 437

Volume 3

8 Error Handling

8.3

Trouble Shooting

Problem

Cause

Solution

No signal

System is not working

Check power supply

Count rate too low

Shielding not open or not open correctly. Check lock and secure it in position OPEN

Alignment of the effective radiation
towards the detector is incorrect

Correct and optimize alignment

Container installations in the beam path

Offset irradiation plane

Wall deposits in the container

Remove wall deposits or perform new calibration if
wall deposits cannot be removed.

Source has reached the end of its service
life

Replace source

No or incorrect level
reading

Entry of final level end values incorrect

Check calibration values and level reading

Level reading fluctu-
ates strongly

Time constant too small

Increase time constant in the Parameter menu
(min. 20s)

Wrong calibration

Check calibration values

Rapid switchover with too small Sigma
value

Increase Sigma value or disable automatic time
switch

Count rate too low
(see above)

Check age of source and irradiation level; replace
detector

Level reading shows
drifts

Detector stabilization faulty

Replace detector

Multiplier faulty

Exchange multiplier

Current output at
24mA

Current output faulty or defective.

Recalibrate current output. Then restart detector by

Software Reset

or by turning the power supply off/

on.
If the current output cannot be calibrated, the
detector needs to be repaired.

Содержание LB 480



































































































































































































































































































































































































































































Результаты поиска

Содержание LB 480

Отзывы:

BERTHOLD TECHNOLOGIES LB 480, Руководство пользователя, Страница: 437 / 450

Результаты поиска

Содержание LB 480

Отзывы: