BERTHOLD TECHNOLOGIES LB 480 Скачать руководство пользователя страница 394 | Manualshive

Страница: 394 / 450

background image

54733-10BA2L

3 – 394

02.2017

5 Calibration

Volume 3

5.1

Preparing Calibration

For correct calibration of the measuring system, you have to ensure
that the detector and basic settings are correct.



Turn the HART

®

Communicator on.

After power on, the Start menu appears.

Tip

Push

HOME

to return from any level back to the Start menu.

If the detector has been in stock for a long time, it may happen that
the internal clock no longer displays the current date. In this case,
the error message

105 Real time clock not valid

is displayed. Update

the date and time to reset the error message (see

).

If you are sure that the detector and basic configuration are correct,
you can start with the calibration of the measuring system immedi-
ately as described in

Otherwise proceed as follows:



If the device is still locked with a password, undo the password
protection (see



Reset the detector to factory defaults (see

chapter 5.1.2

)



Adjust the value for HV default (see

). This is usu-

ally not necessary, since the detector is factory-calibrated.

«
...
392
393
394
395
396
...
»

Содержание LB 480



































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LB 480

Бренд: VEE GEE Страницы: 2

Бренд: E+E Elektronik Страницы: 32

Бренд: ICP DAS USA Страницы: 71

HYDROTECHNIK MultiHandy 2025

Бренд: ICS Страницы: 8

Бренд: ICT International Страницы: 24

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: TC Electronic Страницы: 20

Clavinova CVP-805

Бренд: Yamaha Страницы: 112

Clavinova CLP-270

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 3

Бренд: Kawai Страницы: 8

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Energometrika Страницы: 39

Бренд: IFM Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды