Figure 2a
Locating
Dowel
Locating
Dowel
Large Bowls Small Bowls
17 in (43.18cm)
diameter or
larger bowls
11.5 in (29.21cm)
to 17 in (43.18cm)
diameter bowls
Flip Tower
Battery Compartment,
Water Tube
& Water Pump
CONTENTS:
Assembly
Water
Pump
Battery
Compartment
(4 1.5v D
Batteries
Not Included)
Water Pump
Tube
Battery
Compartment
Screws x2
Start/Stop
Button
Bowl
(Not Included)
Minimum
Water Level
(4 inches from
bottom of
Fountain Base)
Fountain
Base
Fountain
Top
Dancing
Water
Attachments
Recommended minimum bowl size
is approximately 12 inches
Diagram 1a:
O W N E R S M A N U A L
Flippable Fountain Tower
TM
INSTALLING BATTERIES:
1. Lift Fountain Top with Battery Compartment & Water
Pump out of the Fountain Base (Figure 5). Disconnect
the Water Tube from the Battery Compartment.
2. Unscrew (counter clockwise) the Battery Compartment
Screws, slip pump cable out of cable notch, and open cover (Figure
1a, 1b). Note: Cover fits tightly
3. Insert x2 D Batteries with the (+) side facing up in
Battery Compartment and x2 D Batteries with the (-) facing up in
Battery Compartment (Figure 2a).
4. Reinstall the Fountain Top by aligning the locating dowel in
the Battery Compartment and Fountain Top. Set the Battery
Cover down onto the Battery Compartment ensuring the dowel
sets into the alignment hole and that the pump wire is placed back in
the cable notch. Apply pressure and tighten the Battery Cover
Screws by turning clockwise. NOTE: Pressure must be applied to
the Battery Compartment while tightening the screws for the
threads to catch and assure the compartment is properly sealed. If
needed while holding battery compartment and place upside-down
on an even surface to tighten screws
1. Take the Fountain Top/Battery Compartment and Water Pump, connect one side of the Water Tube to the Water Pump and the other end to the bottom side of the
Battery Compartment (A & B of Figure 4).
2. Find a suitable bowl and place it on a flat, level surface. Place the Fountain Base, without the Fountain Top with Battery Compartment and Water Pump, into the center of the bowl.
3. Lower the Fountain Top with Battery Compartment and Water Pump into the Fountain Base.
you align the Fountain Top to the Fountain Base. Fit these into place and your Fountain Top and Base should be secure. Fountain Battery Compartment should be flush with fountain top (Figure 6).
4. Fill bowl with water, water level should be 4 inches from the bottom of the Fountain Base. (Diagram 1a).
Turn Fountain on and set timer: When the Fountain is off, set the run time from 1 to 4 hours by slowly pressing the button 1 to 4 times (Figure 7a & 7b). 3 seconds after
pressing the button, the LED light will repeatedly flash the number of times the button was pressed (Figure 7a). This indicates the number of hours the Fountain will run every day.
The Fountain will turn on at the same time, for the selected number of hours, daily thereafter.
Stop Fountain for one day: To stop the Fountain manually for one day, hold the button for over 2 seconds (Figure 7a &7b). The Fountain will turn off for one day, but will still turn on at
the same time, for the same number of hours selected, daily thereafter.
Reset/Change the timer: To change the run time, stop the Fountain if its running by holding the button for over 2 seconds (Figure 7a and 7b). The Fountain will stop. Once the Fountain is
off, you can press the button again to set the duration (See Step 1). Fully shut off and clear timer: To fully turn off the Fountain so that it will not turn on automatically the next day, press hold
the button for over 2 seconds to turn it off (Figure 7a &7b). When the Fountain is NOT operating, simply press hold the button again for over 2 seconds, the LED will come on for 3
seconds steady to confirm daily program is off.
DANCING WATER ATTACHMENTS: (OPTIONAL): To prevent overspray there are 3 Dancing Water Attachments designed for large bowls and 1 designed for small bowls please use
accordingly. When Fountain is not running, select one of the Dancing Water Attachments and attach to the outlet in the middle of the Fountain Tower (Figure 8a, 8b & 8c).
*PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO ASSEMBLE YOUR NEW FOUNTAIN
Figure 6
Figure 5
Figure 1b
Figure 1a
Figure 3b
Figure 4
Figure 7
A
B
Figure 3a
STEP
2.
STEP
3.
STEP
CHANGING BATTERIES:
1. Remove any Dancing Water Attachment, lift Battery
Compartment and Water Pump out of the Fountain (Figure 5),
ensure Battery Compartment and Water Pump are completely
dry before opening Battery Compartment. It is important that
no water enters the Battery Compartment.
2. See Installing Batteries Section above on how to reinstall
batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the
Fountain (Figure 6).
Figure 7b
Figure 7a
Button
Button
Figure 7: (Below)
On Spout Side of
Flippable Fountain
Tower Align LED to
green dot for
correct placement.
Battery Compartment
Retaining Screws X2
Battery Compartment
Retaining Screws X2
Battery Cover
O-Ring
Figure 8a
Figure 8b
Figure 8c
Max. Water
Level
(2 inches
from top of
Fountain)
Please note, images of parts
are not to scale with one another.
Battery Cover
O-Rings
Dancing Water Attachments
Please use accordingly
to prevent overspray
Dancing Water
Attachments
Figure 2b