1
6E 7645-01a
6E 7645-01a
Order no. 7590 40 02
Operation instructions
IR configuration hand-held
transmitter for presence
detector
Berker GmbH & Co. KG
Klagebach 38
58579 Schalksmühle/Germany
Telefon: + 49 (0) 23 55/90 5-0
Telefax: + 49 (0) 23 55/90 5-111
www.berker.com
09/2011
97-75904-002
Warranty
We reserve the right to make technical and
formal changes to the product in the interest of
technical progress.
Our products are under guarantee within the
scope of the statutory provisions.
If you have a warranty claim, please contact
the point of sale or ship the device postage
free with a description of the fault to the
appropriate regional representative.
GB
The remote control allows the user to set or
modify settings on the presence detectors
1701 06, 1701 07, 7524 10 01, 7524 10 02.
when the potentiometer is on "auto test". It
allows single and multiple settings.
The SET key is used to send the IR messages
to the occupancy sensors. Multiple settings
can be stored in Memo 1 and Memo 2 and
recalled to set several devices.
Single setting
Example:
do a reset.
Multiple settings
Define the parameters to be changed and
press SET to send.
Example: for 25 minutes and corridor use,
press 20', 5' and corridor.
In the case of 2 opposite states the green LED
denotes ON and the red LED denotes OFF
(except Presence/ Absence).
When no function is selected all LED’s are
OFF.
+
+
+
+
Technical specifications
Power supply : 1x 3V CR2032
Shelf life of battery : 2,5 years
Protection index : IP 30
The acknowledgment LED
blinks during the sending
of the IR message.
Use
Battery replacement
-
LED
Description
Key
Meaning
Indication
Function
Presence
Green LED on
Presence on (automatic mode).
Absence
Red LED on
Absence on (semi automatic mode).
Power Up
Green LED on
The light is automatically switched ON for
30 s after power up.
Red LED on
During warm up phase, the light output is off.
Reset
LED on
To return to factory settings
(Lux = 400, time = 20min., presence on,
power up off and cell active).
Test
LED on
To validate the detection area
Time
LED on
To set the time.
It is possible to add times
Ex.: press 2’ and 5’, time value is 7’.
Day level
1000 Lux
LED on
To set the value on 1000 Lux
Learn
LED on
To learn the current Lux level
Corridor
200 Lux
LED on
To set the value on 200 Lux
Office
400 Lux
LED on
To set the value on 400 Lux
Lux +
LED on
To increase the Lux level (+100)
Lux –
LED on
To decrease the Lux level (-100)
Active cell
Green LED on
The light is continuously measured.
Passive cell
Red LED on
The product doesn't switch the light off even
if the ambient luminosity is sufficient.
Settings available
Presence detectors
1701 06
1701 07
7524 10 01
7524 10 02
Key
Meaning
Indication
Function
Press
LED is on until a setting is changed.
To load/unload Memo 1.
Long press
LED is on during 5s., then blinks until release press.
After release, the LED goes off in case of setting
change.
To save the current setting as Memo 1.
Press
LED is on until a setting is changed.
To load/unload Memo 2.
Long press
LED is on during 5s., then blinks until release press.
After release, the LED goes off in case of setting
change.
To save the current setting as Memo 2.
Short press (<5s)
LED flashes.
To send an IR message of the current setting.
Long press (>5s but <10s)
only available if no setting
active.
LED blinks until release press.
To toggle addressing mode on DALI/DSI
detectors (1701 07, 7524 10 02).
Memo and SET keys
Æ
§
