SW40B/SWH40B/SW60B Series
Submersible Waste
Handler Pumps
INSTALLATION, OPERATION, & PARTS MANUAL
SAFETY INFORMATION
Carefully read and follow all safety instructions in this
manual or on pump.
This is the safety alert symbol.
When you see this
symbol on your pump or in this manual, look for one of the
following signal words and be alert to the potential for
personal injury!
warns about hazards that
will
cause serious
personal injury, death or major property damage if ignored.
warns about hazards that
can
cause serious
personal injury, death or major property damage if ignored.
warns bout hazards that
will
or
can
cause
minor personal injury or property damage if ignored.
The word
NOTICE
indicates special instructions which are
important but not related to hazards.
1.
Read these rules and instructions carefully.
Failure to
follow them could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must com-
ply with their rules.
3. Vent sewage or septic tank according to local codes.
4.
Hazardous voltage. Disconnect electri-
cal power from pump when working on or handling
pump for any reason. Do not use automatic reset
controls with this pump.
5. Always keep pump properly serviced and maintained.
6. Use pump for designed task – that is, pumping domestic
sewage and waste water containing solids. Do not pump
metal particles, rocks, or other hard objects.
7.
Do not pump corrosive or flammable liquids with this
pump.
DESCRIPTION
These submersible wastewater pumps are designed for
sewage, trash, effluent and wastewater removal or transfer,
sump drainage, dewatering, flood control and for circulation.
Internal circuitry detects seal leakage and overheating of
windings. Available options include lift-out system compo-
nents, control panels, switches and alarms.
NOTICE:
This unit is not designed for applications involving
salt water or brine! Use with salt water or brine will void
warranty.
SPECIFICATIONS
Power Supply Required: . . . . . . . . . . . . . .230/208-230/460
(See the “Motor” Specifications Chart)
Motor Duty: . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intermittent
Maximum Liquid Temperature: . . . .1 Phase – 104° F (40°C)
3 Phase – 140° F (60°C)
Discharge Adapter: . . . . . . . . . . . . . . . . . . . . . . . . .4” or 6”
Power Cable: . . . . . . . . . . . . . . . . . . . . . . .Type SO or STO
Volute, Impeller, Pump Body: . . . . . . . . .Class 30 Cast Iron
Wear Ring and Impeller Bushing: . . . . . . . . . . . . . . .Bronze
O-Rings and Elastomer part of Shaft Seals: . . . . . . .Buna-N
Shaft Seal Faces: . . . . . . . . . . . . .Carbon and Ceramic with
Stainless Steel Trim
Fasteners in contact with liquid
being pumped: . . . . . . . . . . . . . . . . . . . . . . .Stainless Steel
©2004
Printed in U.S.A.
BE501 (Rev. 4/15/04)
293 Wright Street • Delavan, WI 53115
New Model Number
Original Model Number
SW40300225MB
40SW1-4013
SW40300325MB
40SW3-4013
SW40500225MB
40SW1-4011
SW40500325MB
40SW3-4011
SWH40750325MB
40SWHH3-4513
SWH401000325MB
40SWHH3-4512
SWH401200325MB
40SWHH3-4511
SW60750325MB
60SW3-6013
SW601000325MB
60SW3-6012
SW601200325MB
60SW3-6011
MODEL NUMBER CROSS
REFERENCE CHART
