manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, Руководство пользователя

Поделиться
Скачать
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM Скачать руководство пользователя страница 7

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

7

 

1. 

General information 

This user handbook is intended for use by qualified professionals and contains information on the as-
sembly, installation, start-up and maintenance of the device. 

1.1.  Notes on the handbook 

This user handbook is a component of the product and applies to the following devices: 

 

B-PRIMIS DC-PRIME DC2110W Dialog Controller X CM and DC2115WUX CM  

 

B-PRIMIS ET-PRIME Ethernet Terminal ET2110W X CS and ET2115WUX CS 

 
It contains information on the following topics: 

 

Applications 

 

Safety 

 

Mechanical design 

 

Electrical design 

 

Connections 

 

Start-up 

 

Upkeep and maintenance 

 

Decommissioning 

 

Disposal 

 

 

Always keep this user handbook available alongside the product. 

1.2.  Symbols and visual depictions 

The following symbols and visual depictions are used in this handbook: 

 

Symbol 

Meaning 

 

… 

List entry 

 

… 

Individual instruction or list of instructions which can be carried out in any or-

der. 

1. 

… 

2. 

… 

List of instructions which must be carried out in the order given. 

 

 

Additional product information 

 

Содержание B-PRIMIS DC-PRIME DC2110W X CM














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды