manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, Руководство пользователя

Поделиться
Скачать
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM Скачать руководство пользователя страница 42

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

42

 

Temperature measurement AI (T) 

 

 

Fig. 24: example connection: temperature measurement 

Item  Description 

1 

PT 100 with 2-wire connection 

2 

PT 100 with 3-wire connection 

 

 

Only use the corresponding AGND for each input. 

 

Do not connect AGNDs from different channels. 

 

Do not connect to the common GND. The required connections can already be found on the cir-
cuit board. 

 

Cables to the PT100(0) sensors should be connected as directly as possible (avoid the use of 
terminals and terminal blocks). 

 

Only connect PT100(0) sensors to AI (U/T) channels. 

 

2-wire measurement 

Resistance can result in a measurement error, which in the case of long cables with a small cross-
section can be up to 10°. If the temperature of the sensor is known, this deviation can be subtracted by 
the software automatically and compensated (alternatively, use 3-wire measurement). 
 

3-wire measurement 

The nearest AI (U) connection is used to compensate the resistance in the cable. It can only be used 
directly in conjunction with the following AI (U/T) channel. Channels 1 and 2, and also channels 3 and 4 
each form a pair for 3-wire measurement. 

Содержание B-PRIMIS DC-PRIME DC2110W X CM














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды