manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, Руководство пользователя

Поделиться
Скачать
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM Скачать руководство пользователя страница 27

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

27

 

5.1.1.  Connecting the power supply 

  CAUTION 

Live parts! 

 

Before starting any work on the device, switch off all power feeds, including peripherals. 

 
 

ET2110W X CM / ET2115WUX CM 

 

Connect the power supply to plug X100 according to the following table. 

 
 

 

 

 

Fig. 12: Power supply plug X100 

Power supply plug X100 

Pin 

Designa-
tion 

Assignment 

9 

L0+ 24 V 

Power supply 24 V DC (

–15 %/+20 %) 

ET2110W X CS: max. 0.6 A (peak current 1.2 A) 

ET2115WUX CS: max. 0.7 A (peak current 1.2 A)

 

11 

GND 

M0 / GND 

 
 
The following counterparts have been tested for the SC-SMT 3.5 (Weidmüller) plug-in connector and 
are approved for use with the device: 

 

BLZF 3.5/02/180 (F,LR,LH)SN 

 

 

Содержание B-PRIMIS DC-PRIME DC2110W X CM














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды