Berg Engineering & Sales Company NS-11006 Скачать руководство пользователя страница 41

Страница: 41 / 90

Operation and Menu Structure

NewSonic SonoDur-R

Issue 105 06/2020

Page 41

Practical experience gained from the very low exemplary scattering of SonoDur probes has shown

that the adjustments with different testing forces and for all types of probes result in a very good

concordance. Therefore, no distinction, e.g., for the adjustment number CAL, has been made

between testing forces in the material tables F2, F3, F4, F5 (EN ISO 18265) or T4, T7, T8, T9 (ASTM

E140). In any case, the use of a first approximation of an adjustment result for other testing forces is

correct for the correction of the E-Module influence, provided that no surface effects (hardening

layer, roughness) represent issues.

WARNING

Therefore, calibration data can in principle also be used for test probes with different testing forces.
However, this resides in the responsibility of the tester.
In case of doubt, a probe with suitable testing forces should be chosen!

7.10

Conversions

7.10.1

Hardness Scale

The hardness scale can be accessed directly by tapping the current scale in the measurement menu

or via Menu -> Conversions.

7.10.2

Standard (Norm)

The most recent versions of the two conversion standards are available according to ASTM E140 and

EN ISO 18265, respectively - status 2015.

WARNING

Please absolutely comply with the conversion limits. When exceeding or falling below these values
(e.g. in the HB scale), the message

Outside the HB conversion

will be issued and the info window

will display the measured values as being deleted (also refer to the representation of the measured
values outside the conversion limits,

Section 7.10.4 Presentation of the measurement values

outside the conversion limits

Figure 7.74

Содержание NS-11006



























































































Результаты поиска

Содержание NS-11006

Отзывы:

Похожие инструкции для NS-11006

Бренды по названию

Популярные бренды

Berg Engineering & Sales Company NS-11006, Инструкция по эксплуатации

Результаты поиска

Содержание NS-11006

Отзывы:

Похожие инструкции для NS-11006

Бренды по названию

Популярные бренды