background image

2 | Installation

18

The electric panel access panel is wired to the electronic board, so

it must not be completely removed. Pay particular attention not to

disconnect or tear off the wire.

– unscrew the fastening screws
– remove the terminal board cover panel

1

Connection cable to outdoor unit

2

Wire retainer

3

Terminal

– remove the wire retainer
– make the electric connections according to the diagrams on the

installation booklet of the matching outdoor unit

It is compulsory to use ring crimp terminals to connect to the

terminal board.

Refer to the manual of the matching outdoor unit when sizing the

connection cable.

– fasten the wires with the wire retainer
– complete the electric connections and refit all components by

performing the described operations in reverse order

Mandatory items:

– connect the device to a properly functioning earthing system
– for any electrical intervention, always refer to the wiring

diagrams contained within this booklet

– take anti-static precautions in case of weather conditions where

humidity is less than 40%

Electric connections shall be made in compliance with national

regulations.

Avoid placing the connection cables less than 1 metre away from

radio and video systems.

Avoid using mobile phones.

It is forbidden to earth the device together with pipes, lightning

conductors or the earthing system of a telephone line. Using an

improper earthing system can cause electric shocks.

2.15 Remote control

Control, setting and programming operations are carried out with the IR

remote control.
The electronics modulates the device operation according to the

temperatures detected by the probes inside the indoor and outdoor

units.

Battery insertion

The remote control is powered by two 1.5V AAA batteries that must be

inserted into its rear side and protected by a cover.
To insert the batteries:

– remove the cover by pressing it down and lifting it up
– insert the batteries respecting the polarities
– put the cover back in place

Two 1.5V AAA batteries are supplied with the unit for its first

set-up.

Function keys

The remote control features a small door in the key area:

Содержание 20171580


























Отзывы: