background image

 

20 

 

The 

 central  heating  fascia  bar  is  a 

permanent  display  of  the  functioning 
fascia set for the central heating set point 
setting.  If  a  bar  is  completely  blank,  the 
set-point  is  the  anti-frost  level  (central 
heating  OFF).  If  only  the  lower  part  of  a 
bar is black, the set point is the economy 
(T2).  If  the  whole  bar  is  black,  the  set 
point  is  the  comfort  (T1).  They  will 
disappear  when  the  central  heating  is 
turned OFF. 
 

The 

 day  icon  and  the  night  icon 

indicate  whether  the  current  set  point  for 
the current time is night or day. 
 
 
 
 

The 

 party  icon  is  lit  up  when  the 

party  mode  is  selected.  In  this  mode  the 
central  heating  fascia  bar  will  be 
completely  lit  up  at  T1  together  with  the 
day  icon.  After  midnight,  the  display  will 
turn back to the pre-set working fascia. 
 

The 

 holiday  icon  is  lit  up  when  the 

holiday  mode  is  selected.  In  this  mode 
the central heating fascia bar will be lit up 
at  T2  together  with  the  night  icon.  After 
the  holiday  counter  is  over,  the  display 
will  turn  back  to  the  pre-set  working 
fascia. 
 

When the 

 icon appears, the controller 

is  working  as  to  keep  the  anti-frost 
temperature. 
 
 

Содержание 20050684





























Отзывы: