Berchtold CHROMOPHARE F 300 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 67

background image

Claims of any kind due to damage resulting from improper use are excluded.
The operator is solely responsible for damages resulting from improper use.

1.4 Reliability

As single lights, CHROMOPHARE

®

examination lights are extremely reliable be-

cause the LED modules and their lamps are long-lasting.

1.5 Personal protective equipment

To minimise health risks, personal protective equipment must be worn while
working.

¡

When working, always wear the protective equipment appropriate to the
respective task.

¡

Observe the information on the personal protection equipment posted in
the work area.

When performing specific work, special protective equipment is required. These
tasks are discussed individually in the various sections of this manual. The special
protective equipment covered is:

Goggles
Protect workers from any flying parts or sprays of liquids

1.6 Specific risks

The following section lists residual risks identified by a risk analysis.

¡

Observe the following safety instructions and the warnings in the sections be-
low to reduce health hazards and avoid dangerous situations.

Protective equipment for
special tasks

Examination light CHROMOPHARE F 300

Safety

8

«
...
6
7
8
9
10
...
»

Содержание CHROMOPHARE F 300




































































Отзывы:

Нет отзывов

Похожие инструкции для CHROMOPHARE F 300

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: GE Страницы: 24

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: Valcom Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды