Bentel Kyo 100, Руководство по установке, Страница: 83 / 101

thus simplifying the programming process while in-
creasing the security level.
Codes which have not been made Available can be
considered inexistent.
+
NON-Available Codes will be assigned their de-
fault PINs.
+
You cannot toggle the Available status of a Code,
without first entering its Father code PIN .
You cannot toggle the Available status of a Code
when the Active option is Enabled.
Active An Active Code can access and control the
system in accordance with its access level.
A Non-Active Code cannot access the system, how-
ever, it can still be programmed using its Father Code.
Father Codes can toggle the Active status of their as-
signed Codes (also via the User Menu).
+
You cannot toggle the Active status of a Code that
is the sole Father of another Code.
AT Default: ONLY Code No. 001 is Active .
Duress Code If this option is enabled, any Telephone
actions (calls or reports) associated with the Recog-
nized user code event (generated by the Code in
question) will not be signalled on the keypad (i.e.
<@255> will not appear over the i icon).
Patrol Code If this option is enabled, the Code will be
able to perform Disarm and Arm operations ONLY, re-
gardless of its assigned Code Type . Furthermore, if a
Partition is Disarmed by a Code with the Patrol attrib-
ute, it will remain Disarmed for the programmed Pa-
trol Time ONLY, after which, it will Rearm automati-
cally (refer to “Patrol Time” under “Partitions”).
Father Code 1 - 2 - 3 This drop-down list will allow
you to select the Father codes.
Ø
Each Code can have up to 3 Father codes;
Ø
a Code can be programmed as its own Father.
A Father Code can:
Ø
Change the PIN of its assigned Codes ( Sons );
Ø
Enable/Disable the Active status of its assigned
Codes, that is, if they are not Fathers of other Codes;
Ø
Enable/Disable the Available status of its assigned
Codes.
+
YOU CANNOT assign a new Father code to a
code without first entering the PIN of one of its cur-
rent Father codes.
For KYO 300 — Codes no. 132 to 195 (the 64 Tele-
phone Access Codes) CANNOT be Father codes
For KYO 100 — Codes no. 82 to 97 (the 16 Tele-
phone Access Codes) CANNOT be Father codes.
Father codes can be changed by the User.
At default:
Ø Code no. 001 is its own Father code;
Ø
Codes no. 002 to 131 (Codes no. 002 to 81 for KYO
100) have two Father codes: themselves and Code
no. 001;
Ø
Codes no. 132 to 195 (Codes no. 82 to 97 for KYO
100) have one Father code: Code no. 001.
n
Enable on Partitions
The Enable on Partitions Table will allow you to select
the Partitions the Code will be able to control and set the
A, B, C and D Arming modes, as follows.
Partitions The Partitions line (first line) shows the
Control Panel Partition ID Numbers.
+
If you click the Description button (at the bottom of
the page), the application will show the Partition
Description.
The check boxes on the second line will allow you to se-
lect the Code Partitions.
Ø
Box ticked: the Code CAN operate on the corre-
sponding Partition.
Ø
Box empty: the Code CANNOT operate on the corre-
sponding Partition.
To DISABLE the Code on all the Partitions: click the
Partitions button (bottom of page) then select None .
To ENABLE the Code on all the Partitions: click the Par-
titions button (bottom of page) then select All .
To toggle the current Enabled/Disabled status of the
Code: click Partitions button (bottom of page) then se-
lect Invert selection .
+
Code commands will affect ONLY the Partitions
(and subsequently the Zones) common to both the
Code and Keypad in use.
A This line will allow you to select the A Mode Arming
configuration of the Partitions.
Double click on the Partition field until the required
mode is shown ( D , N , A , S or I ), or right click the Parti-
tion field then select the required mode from the
drop-down list.
Arming Modes
Ø
D = Partition will Disarm
Ø
N = no operation
Ø
A = Partition will Arm in Away mode
Ø
S = Partition will Arm in Stay mode
Ø
I = Partition will Arm in Stay mode with zero delay (In-
stant)
B As for A but for B Mode Arm commands at a Keypad.
C As for A but for C Mode Arm commands at a Keypad.
D As for A but for D Mode Arm commands at a Keypad.
n
Associated Timer
If a Code is associated with a Timer, it will function only
during the programmed Timer slots (refer to “Scheduler
- Timers”).
82