USER MANUAL
KYO100-KYO300
9
)&&)*
Press the
E
key to exit.
T
T
T
T
T
Partition status enquiry
Press the
O
key to view the status of the Keypad Par-
titions:
!!../"..!!!!.
../""..!....
The first line of the display will show (from right to left)
the status of Partitions no. 1 through no. 16, the second
row of the display will show (from left to right) the status
of Partitions no. 17 through no. 32. The hyphen (–) indi-
cates that the Partition is not a Keypad Partition.
The Partition status will be shown for approximately 6
seconds.
Partition status enquiry is possible on Enabled Key-
pads only. If Partition Alarm or Tamper is present
the respective character will blink.
Accessing the User menu
(<
Code
>
E
)
(for MIA/D, Alison-S and Alison-DV Keypads)
Enter a valid User Code then press the
E
key to access
the User menu. The User menu will allow Users to ac-
cess ONLY the commands they are enabled for.
You can access the User menu when the Control
panel is Armed or Disarmed.
Using
C
and
D
, scroll for the required option then
press the
E
key.
Press
e
as many times as required to step back and
exit the menu.
Several Users can access the menu at the same
time from different keypads.
The User menu provides the following options:
Reset Alarms
Stop Alarms
Arm/Disarm
Overtime request
Teleservice request
Enable/Disable auto-arm
Enable/Disable Teleservice
Enable/Disable Answering device
Disable buzzer
Change Telephone number
Program PINs
Change Time and Date
Reset PC Programming
Test Keypad
Test Siren
Activate Outputs
Zone status
Continuous recording
Memo
Event logger
Clear call queue
Enable/Disable Timers
Enable/Disable Key
Your Installer has programmed your Control panel
with your requirements in mind. Therefore, some of
the options may not be available.
This system can manage 195 User Codes. Only the first
User Code (
0001
) is
Active
and can operate the system.
Your Installer will enable and program as many User
Codes as necessary. The programmed Access Level de-
fines the User Code Partitions (the Partitions the User
Code can control) and the User Code options (the op-
tions the User Code can access).
The menu will show
the options the entered User Code is enabled for.
The following paragraphs describe all the Options on the
User menu.
The commands will affect ONLY the common Parti-
tions of the User Code and Keypad in use.
T
T
T
T
T
Reset Alarms and Tamper
This command will allow you to restore all Alarm signal-
ling devices to Standby, and delete the zone and Parti-
tion Alarm memories.
Once the command has been executed, the display will
show the following message:
&$#&
.32/
If Alarm signalling persists after a
Reset Alarms
com-
mand, select the
Stop Alarms
option. The causes of
persistent Alarms must be cleared immediately.
T
T
T
T
T
Stop Alarms
This command will allow you to stop and freeze all the
Alarm signalling devices. This status can be undone by
pressing any key. During this phase the Control panel
will be unable to trigger Alarms, and the display will show
the following message:
01/+230
01/+230
Õ
Õ
The
I
indicators on Keypads, assigned to any of the
Partitions of the Keypad in use, will blink.
T
T
T
T
T
Arm/Disarm
This command will allow you to Arm or Disarm the Parti-
tions one by one, as follows:
Figure 2 - Partition status
Содержание KYO 100
Страница 1: ......
