background image

11

BYPASS MODE

The “Bypass” mode is entered by pressing keys + and – simultaneously.

ON: 

 

ESA BASIC keeps the control unit connected to it always on. In this way, parameters and logics of the control unit 

can be preset, thus avoiding that the control unit enters the SLEEP mode.
N.B.: when the BYPASS mode is ON, the wording “ON” is displayed.

OFF: 

  ESA BASIC works regularly.

HOW TO PROGRAMME

The programming of the various functions of the control unit is carried out by using the LCD display on the control unit and 
presetting the desired values in the programming menus described hereunder.

USE OF THE PROGRAMMIN PUSH BUTTONS

Press OK to access the Main Menu (PAR>>LOG>>RADIO>>...) that can be selected by pressing keys + and -.
Select the Main Menu by pressing <OK> to access the desired Function Menu.

t5PTDSPMMUIF'VODUJPO.FOVGSPNUPQUPCPUUPNQSFTTUIFLFZ
t5PTDSPMMUIF'VODUJPO.FOVGSPNCPUUPNUPUPQQSFTTUIFLFZ
t#ZQSFTTJOHUIF0,LFZBDDFTTJTFOBCMFEUPBOZQPTTJCMFQSFTFUUJOHUPCFNPEJmFE
t5IFQSFTFUWBMVFTDBOCFDIBOHFECZQSFTTJOHBOELFZT
t*G0,JTQSFTTFEBHBJOUIFWBMVFJTQSPHSBNNFEBOE0,JTEJTQMBZFE

See section “Programming Example”.

NOTE: 

If keys <+> and <-> are pressed simultaneously from a Function Menu, this allows to return to the upper menu without 
making any changes.
To speed up the increase/decrease of values, keep key <+> or key <-> pressed.
After waiting 30 seconds, the control unit exits the programming mode and switches the display off.

PARAMETERS, LOGICS AND SPECIAL FUNCTIONS

The single functions available in the control unit are described in the following table.

MENU

FUNCTION

MIN-MAX

(Default)

MEMO

PARAMETERS

toff

Self-switching  off  time:  when  the  preset  time  has  elapsed,  if  the  system  is 
still in standby mode (powered control unit with motor stopped), ESA cuts off 
power to the control unit.
If  one  of  the  N.C.  inputs  is  kept  open  (e.g.  photocell  obscured),  the  self-
switching  off  time  will  not  be  calculated  until  the  input  recovers  its  regular 
operating mode.

N.B.: preset a TOFF higher than the TCA time preset in the control unit.

10-3600 sec

(60)

STD1

Start Delay channel 1: delay between the activation of input 1 and its replication 
OUT 1 when the control unit is in SLEEP mode (this delay is the time required 
for the control unit to switch on and being able to receive a control signal sent 
by ESA).

0.1-15.0 sec 

(2,0)

STd2

Start Delay channel 2:

----

-------

STd6

Start Delay channel 6:

tch1

The switch time of the channel 1 relay is preset.

0.1-90.0 sec 

(1,0)

TCH2

The switch time of the channel 2 relay is preset.

----

-------

TCH6

The switch time of the channel 6 relay is preset.

Intelligent Security & Fire Ltd.

Содержание ESA BASIC









Отзывы: