background image

9

EC declaration of confirmity 

Manufacturer: 

Automatismi Benincà

 SpA.

Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italia

Herewith declares that: energy-saving device

 

 

ESA BASIC

.

complies with the following relevant provisions:
EMC guidelines: 

89/336/CCE, 93/68/CEE

Low voltage guidelines: 

73/23/CEE, 93/68/CEE

Benincà Luigi, Legal responsible.
Sandrigo, 08/04/2010.

WARNINGS

This  manual  has  been  especially  written  to  be  use  by 
qualified fitters.

None  of  the  information  provide  in  this  manual  can  be 
considered as being of interest for the end users. 

Preserve this manual for future needs. 

The technician has to furnish all the information related to 
the step by step function, the manual and the emergency 
function of the operator, and to deliver the manual to the 
final user. 

;

Foresee on the supply net an onnipolar switch or 
selector  with  distance  of  the  contacts  equal  or 
superior to 3 mms. 

Verify that of the electrical system there is an awry differ-
ential interrupter and overcurrent protection.

Some typologies of installation require the connection of 
the shutter to be link at a conductive mass of the ground 
according to the regulations in force.

The  electrical  installation  and  the  operating  logic  must 
comply with the regulations in force.

The leads fed with different voltages must be physically 
separate, or they must be suitably insulated with additional 
insulation of at least 1 mm.

The leads must be secured with an additional fixture near 
the terminals.

During installation, maintenance and repair, interrupt the 
power supply before opening the lid to access the electri-
cal parts

Check all the connections again before switching on the 
power.

The unused N.C. inputs must be bridged.

The descriptions and the present illustrations in this manual 
are not binding. Leaving the essential characteristics of the 
product  unchanged,  the  manufacturer  reserves  himself 
the  right  to  bring  any  change  of  technical,  constructive 
or  commercial  character  without  undertaking  himself  to 
update the present publication. 

TECHNICAL DATA

Mains power supply

From 85 to 260 VAC 50/60 Hz

Protection level

IP40

Operating temperature 

-20°C / +70°C

Radio receiver

433,92 MHz, incorporated and configurable

No. of codes storable in memory

512

Consumption in sleep mode

150 mW

Power contact range

16A/250Vac resistance load

Intelligent Security & Fire Ltd.

Содержание ESA BASIC









Отзывы: