Benefon DELTA TDP-40-TN2 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 208

background image

28.1.1999

XO0244E4_fm5.fm

6

Product: HPT-40 (Desktop Charger) / YO0244

reserve battery. The phone is provided with its full requirement, so that the remaining
current is avilable to charge the reserve battery (1500 mA - current called for by
phone). When charging only the reserve battery, current equivalent to its capacity is
supplied.

The charging indicator (green led) flashes during the whole of the quick-charge
phase. After quick-charge the battery capacity has been charged 70...80%. The
change is made from quick-charge to continuous charge when one of the following
terms is fulfilled:

a) The battery voltage exceeds its instantaneous correspondingtemperature
limit, according to the following formula: V = 7.5 -11.25 mV x (T-20), where T is
the battery temperature (+10...+40 C)

b) The battery has been charged to its nominal capacity.

7.3.3.2 Continuous charging

When changing to continuous charging, there is approx. 20...30% of battery capacity
left to charge. The continuous charge duration depends on the total capacity of the
battery under charge. The battery is charged with a current corresponding to 1/4 of
its capacity. If the temperature rises above +55 C, then a NiMH battery is charged
with a current 1/30 of its capacity, and a NiCd battery with a current 1/10 of its capac-
ity, until the battery temperature returns to +40 C.

The change to stand-by charging takes place when the last of the battery capacity
has been charged. The charging indicator (green led) flashes throughout the contin-
uous charging phase. The battery capacity after continuous charging is 100%.

7.3.3.3 Stand-by charging

The charging current during stand-by charging depends on the type of battery under
charge (1/10 NiCd capacity; 1/30 NiMH capacity). Stand-by charging is the last
phase in the charging sequence, and continues as long as the battery remains in its
holder. The charging indicator (green led) is now lit continuously.

7.3.4 Discharging the reserve battery

The discharge sequence is initiated by pressing the discharge button on the holder
for approx. 1 s. with the battery in its holder. The battery is discharged until its volt-
age drops to approx. 4.5 V (or the battery is removed from the holder). This is fol-
lowed by the charging sequence 1..3. During the discharge sequence, the discharge
indicator (red led) is lit. The battery voltage is measured under load. During dis-
charge, the desktop charger up-dates the battery charge counter in the memory
within the battery pack.

«
...
115
116
117
118
119
...
»

Содержание DELTA TDP-40-TN2

















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DELTA TDP-40-TN2

Бренд: Olympia Страницы: 68

Бренд: Yealink Страницы: 6

Бренд: Yealink Страницы: 2

Бренд: Tadiran Telecom Страницы: 7

Бренд: Obihai Страницы: 12

Бренд: Obihai Страницы: 220

Бренд: Netway Страницы: 68

Бренд: Sangoma Страницы: 9

Smartphone Portable Keyboard

Бренд: Kyocera Страницы: 36

Бренд: Wistec Страницы: 60

Бренд: Sagem Страницы: 72

Бренд: Ulefone Страницы: 47

Бренд: Talk To Me Technologies Страницы: 2

Бренд: Audiovox Страницы: 49

Бренд: Samsung Страницы: 182

Бренд: Samsung Страницы: 193

Бренд: Samsung Страницы: 2

Бренд: Acer Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды