BendPak XPR-12CL, Инструкция по установке и эксплуатации

Страница: 6 / 64

6
INTRODUCTION
• Read and understand all instructions and all safety warn-
ings before operating lift.
• Care must be taken as burns can occur from touching
hot parts.
• Do not operate equipment with a damaged cord or if the
equipment has been dropped or damaged until it has
been examined by a qualified service person.
• Do not let a cord hang over the edge of the table, bench,
or counter or come in contact with hot manifolds or mov-
ing fan blades.
• If an extension cord is necessary, a cord with a current
rating equal to or more than that of the equipment should
be used. Cords rated for less current than the equipment
may overheat. Care should be taken to arrange the cord
so that it will not be tripped over or pulled.
• Always unplug equipment from electrical outlet when not
in use. Never use the cord to pull the plug from the outlet.
Grasp plug and pull to disconnect.
• Let equipment cool completely before putting away.
Loop cord loosely around equipment when storing.
• To reduce the risk of fire, do not operate equipment near
open containers of flammable liquids (gasoline).
• Adequate ventilation should be provided when working
on operating internal combustion engines.
• Keep hair, loose clothing, fingers, and all parts of body
away from moving parts. Keep feet clear of lift when low-
ering. Avoid pinch points.
• DANGER! To reduce the risk of electric shock, do
not use on wet surfaces or expose
to rain. The power unit used on this
lift contains high voltage. Disconnect
power at the receptacle or at the circuit
breaker switch before performing any
electrical repairs. Secure plug so that
it cannot be accidentally plugged in
during service. or mark circuit break-
er switch so that it cannot be acci-
dentally switched on during service.
• BendPak requires all operators to read and be familiar
with ANSI/ALI ALIS Safety Requirements for Installation
and Service of Automotive Lifts .
• ALWAYS WEAR SAFETY GLASSES. Everyday eye-
glasses only have impact resistant lenses, they are not
safety glasses.
• Consider work environment. Keep work area clean.
Cluttered work areas invite injuries. Keep areas well lit.
• Guard against electric shock. This lift must be grounded
while in use to protect operator from electric shock.
Never connect the green power cord wire to a live termi-
nal. This is for ground only.
• Only trained operators should operate this lift. All non-
trained personnel should be kept away from the work
area. Never let non-trained personnel come in contact
with, or operate lift.
• DO NOT override self-closing lift controls.
• Clear area if vehicle is in danger of falling.
• ALWAYS make sure the safeties are
engaged before attempting to work on or
near a vehicle.
• WARNING! RISK OF EXPLOSION. This
equipment has internal arcing or spark-
ing parts which should not be exposed to
flammable vapors. This machine should not be located
in a recessed area or below floor level.
• MAINTAIN WITH CARE. Keep lift clean for better and
safer performance. Follow manual for proper lubrication
and maintenance instructions. Keep control handles
and/or buttons dry, clean and free from grease and oil.
• Check for damaged parts. Check for alignment of mov-
ing parts, breakage of parts or any condition that may
affect operation of lift. Do not use lift if any component is
broken or damaged.
• NEVER remove safety related components from the lift.
Do not use lift if safety related components are missing
or damaged.
• STAY ALERT. Use common sense and watch what you
are doing. Remember, SAFETY FIRST.
SAVE THESE INSTRUCTIONS
1. Carefully remove the crating and packing materials.
CAUTION! Be careful when cutting steel banding material
as items may become loose and fall, causing injury.
2. Check the voltage, phase, and proper amperage
requirements for the motor shown on the motor plate.
Wiring should be performed by a certified electrician only.
IMPORTANT SAFETY INSTRUCTIONS
Read these safety instructions entirely.
IMPORTANT NOTICE
Do not attempt to install this lift if you have never been trained on basic automotive lift installation procedures.
Never attempt to lift components without proper lifting tools such as forklift or cranes.
Stay clear of any moving parts that can fall and cause injury.