BendPak LR-10000 Скачать руководство пользователя страница 34

Страница: 34 / 44

LR-10000 Low-Rise Scissor Lift

P/N 5900075 — Rev. A1 — April 2019

Maintenance

⚠

DANGER

Before performing any maintenance, make sure the Lift is completely disconnected
from power and

cannot

be re-energized until all maintenance is complete.

BendPak strongly recommends using your Power Disconnect Switch during
maintenance. If your organization has Lockout/Tagout policies, make sure to

implement them during all maintenance.

To maintain your Lift

•

Daily

: Keep the Lift clean. Wipe up any oil spills, clean any dirt.

•

Daily

: Make a visual inspection of all moving parts and check for damage or excessive wear. If

you find any damaged or worn parts, take the Lift out of service until they are replaced.

•

Daily

: Make sure the Safety Locks are in good operating condition. If you find that the Safety

Locks are damaged or excessively worn, take the Lift out of service until they are replaced.

not use your Lift if the Safety Locks are damaged or excessively worn

•

Weekly

: Check all controls to make sure they are functioning normally.

•

Weekly

: Check all labels on the unit. Replace them if they are illegible or missing.

•

Monthly

: Lubricate the grease fittings. We recommend using white lithium grease or similar.

•

Monthly

: Check the Power Unit’s Hydraulic Fluid levels. Refill if low.

•

Every two months

: Check all Anchor Bolts to make sure they are tight. If not, tighten them.

⚠

WARNING:

Do not operate your Lift if you find issues; instead, take the Lift out of service, then

contact your dealer, email

[email protected]

, visit

bendpak.com/support

, or call

(800) 253-2363

, extension 196.

Lubrication

The following drawing shows the lubrication points for the Lift. Note that some lubrication points are

under other parts of the Lift.

Содержание LR-10000












































Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды

BendPak LR-10000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LR-10000

Отзывы:

Похожие инструкции для LR-10000

Бренды по названию

Популярные бренды