manualshive.com logo in svg

BendPak HD-14T, Инструкция по установке и эксплуатации

BendPak HD-14T - высококачественный автомобильный подъемник, предназначенный для профессионального использования. Для правильной установки и эксплуатации необходимо ознакомиться с Руководством по установке и эксплуатации. Скачайте это руководство бесплатно на manualshive.com и получите полезные инструкции для использования данного оборудования.

Поделиться
Скачать
background image

 

HD-14T Four Post Lift 

37

 

P/N 5900037 — Rev. F — February 2022 

 

IMPORTANT! PLEASE READ NOW 

 

Hydraulic Fluid Contamination 

Hydraulic Fluid Contamination poses a 

serious

 issue for your Lift; contaminants such as water, dirt, 

or other debris can get into the Hydraulic Hoses and Fittings on your Lift, making your new Lift 

inoperable. 
Your Lift is shipped with clean components; however, BendPak strongly recommends that you take 

secondary precaution and clean all Hydraulic Hoses and Fittings prior to making connections. It is 

better and less costly to take these extra steps now so that you do not need to take your Lift out of 

service later to fix issues that could have been prevented at the time of installation. 
There are several ways to clean Hydraulic Hoses and Fittings: 
•

 

Compressed Air

. Use an air compressor to blow out contaminants from each Hydraulic Hose 

and Fitting prior to installation. Clean, dry air is preferred. Wear eye protection (safety glasses, 

goggles, or face shield) when using compressed air for cleaning. Never point an air hose nozzle at 

any part of your body or any other person. 

•

 

Fluid Flushing

. As long as the Hydraulic Fluid is clean and compatible with the system fluid, you 

can flush Hoses and Fittings to create turbulent flow and remove particulates. Always ensure that 

the fluid itself is contaminant-free. 

Some additional steps that will help keep the Hydraulic Fluid clean: 
•

 

Remove old thread seal tape

. Some ports on the Hydraulic Cylinders are shipped with 

temporary plugs secured with thread seal tape, so make sure to thoroughly remove any leftover 

thread seal tape that may inadvertently enter the Hydraulic System. 

•

 

Use a liquid thread sealant only

. Teflon paste-type thread sealant or Loctite™ 5452 thread 

sealant is recommended for all NPT Fittings. Do not over tighten NPT Fittings or they may crack. 

Never use thread seal tape on JIC Fittings or ORB O-Ring Fittings. 

•

 

Always use clean equipment

. If you use a dirty bucket or funnel to transfer the Hydraulic Fluid 

into the Hydraulic Fluid Reservoir, the contaminants will likely be introduced into the Fluid. When 

using cleaning rags, use a lint-free rag. 

•

 

Proper storage

. Keep the Hydraulic Fluid sealed in its container until ready for use; store the 

Fluid in a clean, dry, and cool area. 

•

 

Cover the Hoses and Fittings

. Before installation, do not leave the ends of the Fittings 

exposed; the same applies for the Hydraulic Hoses. As a general rule, keep the Hydraulic Hoses 

and Fittings capped and kept clean in a clean area until ready for use. 

•

 

Filter the new Hydraulic Fluid

. Just because it is new does not necessarily mean it is 

clean

. 

Use an offline filtration cart or kidney loop system to make sure the Hydraulic Fluid is clean before 

being transferred into the Hydraulic Fluid Reservoir (even using a heavy duty nylon mesh screen is 
better than trusting what is left at the bottom of the barrel). 

•

 

Avoid mixing different types of Hydraulic Fluid

. If Hydraulic Fluid needs to be replaced, 

make sure to flush the Hydraulic System of the old Hydraulic Fluid before you add the replacement 

Fluid; do not mix the two together. 

Содержание HD-14T













































































Отзывы:

Нет отзывов

Похожие инструкции для HD-14T

Happ 27 Installation And Operation Manual preview
27
Бренд: Happ Страницы: 49
KegLand BrewZilla 100L - Gen 4 Instruction Manual preview
BrewZilla 100L - Gen 4
Бренд: KegLand Страницы: 48
Vulcan-Hart PROTIG 165 Owner'S Manual preview
PROTIG 165
Бренд: Vulcan-Hart Страницы: 28
Simplex F18804 Installation Instructions Operating Instructions preview
F18804
Бренд: Simplex Страницы: 40
Evil Mad Scientist Ostrich Eggbot 2.0 Assembly Manual preview
Ostrich Eggbot 2.0
Бренд: Evil Mad Scientist Страницы: 45
Challenger Lifts Versymmetric VLE10 Installation, Operation & Maintenance Manual preview
Versymmetric VLE10
Бренд: Challenger Lifts Страницы: 15
PACH & COMPANY AeGIS 8000 Series Quick Installation Manual preview
AeGIS 8000 Series
Бренд: PACH & COMPANY Страницы: 14
GYS TITANIUM 400 AC/DC Manual preview
TITANIUM 400 AC/DC
Бренд: GYS Страницы: 120
Paton PROMIG-160 Instruction Manual preview
PROMIG-160
Бренд: Paton Страницы: 50
Century OM-117071002 Operator'S Manual preview
OM-117071002
Бренд: Century Страницы: 27
Miller Electric STR 450 Owner'S Manual preview
STR 450
Бренд: Miller Electric Страницы: 32
Lincoln Electric Multi-Weld 350 Brochure & Specs preview
Multi-Weld 350
Бренд: Lincoln Electric Страницы: 6
AUTEC ALM-10040FL User & Installation Manual preview
ALM-10040FL
Бренд: AUTEC Страницы: 37
Still LiftRunner B frames Original Instructions Manual preview
LiftRunner B frames
Бренд: Still Страницы: 108
IFM ANT420 Operating Instructions Manual preview
ANT420
Бренд: IFM Страницы: 15
Geberit ESG 3 Maintenance Manual preview
ESG 3
Бренд: Geberit Страницы: 28
GEA D 10 Settings And Malfunctions preview
D 10
Бренд: GEA Страницы: 96
GCE LORCH PROPALINE LOMEN Instructions For Use Manual preview
LORCH PROPALINE LOMEN
Бренд: GCE Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды