manualshive.com logo in svg

Bender LINETRAXX RCMS150, Руководство пользователя

Поделиться
Скачать
Bender LINETRAXX RCMS150 Скачать руководство пользователя страница 12

Product description

12

RCMS150_D00259_01_M_XXEN/08.2021

If one of the four set response values 

I

ΔN…

 is exceeded, the assigned response delay 

t

on…

 starts. If the response value continues to be exceeded, the corresponding alarm 

message (prewarning or main alarm) is indicated on the gateway after the response de-
lay 

t

on…

 has elapsed. 

In the event of a main alarm, the alarm LED of the respective channel K1…6 lights up 
yellow.

A pending alarm message is emitted via the BMS or Modbus interface with address and 
measuring channel indication and can be evaluated by means of a gateway. 

If the recorded residual current falls below the release value (response value minus hys-
teresis) the delay on release 

t

off

 begins. If the value remains below the release value af-

ter 

t

off

 has elapsed, the LED of the respective channel goes out. The alarm message is 

reset on the interface. 
If the fault memory is enabled (only applicable to RCMS150-01), the alarm message re-
mains on the bus despite the LED going out.

All devices can be accessed via the network from any PC using a standard web browser. 
Like this, all relevant measurement data of the monitored system are available. All de-
vice-related parameters of the RCMS150… can be set via the gateway technology.

To ensure the device function, a continuous automatic self test is run, which monitors 
the function of all measuring current transformers. In the event of a device error, the 
alarm LED of the respective channel flashes and an error message is output via the in-
terface. 

During the manual self test, a residual current is induced in the respective current trans-
former at each individual channel K1…6 one after the other via test windings and it is 
checked whether the corresponding main alarm is triggered. The duration of the test 
depends on the response delays of the main alarms.

3.3 Approvals and certifications

 

UL508

 in preparation

 

CSA

 in preparation

 

LR

 in preparation

Содержание LINETRAXX RCMS150





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды