background image

 

 

 

 

 

Unpacking the Appliance 

·

 

The heater is supplied in a single pack carton.   

·

 

All instructions should be read prior to unpacking or installing the appliance.   

·

 

Ensure all parts including loose items have been removed prior to discarding the packaging.   

·

 

Product Checklist 

·

 

1 piece: Electric heater 

·

 

1 piece:

 

Fret

 

·

 

2 piece:

 

Feet 

·

 

1 piece:

 

Coal Bed 

·

 

1 piece: Instruction manual   

 

·

 

WARNING:

 This heater is not equipped with a device to control the room temperature. Do not use this heater in small 

rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is 

provided.

 

·

 

CAUTION

- Some parts of this product can become very hot and cause burns. Particular attention has to be given where 

children and vulnerable people are present.

 

 

 

Installation Instructions 

 

·

 

Do not connect the heater to the mains power supply until all of the instructions have been read and the heater has been 

properly and securely fitted.     

·

 

This heater MUST be earthed. If in any doubt consult the manufacturer, its service centre or a qualified person 

·

 

This heater must not be directly placed on a carpet or similar material. We recommend that it is placed onto a hearth or 

similar non-combustible material. 

·

 

The heater is suitable for installation into a location that has an opening size within the guidelines shown below: 

 

 

 

 

 

 

 

·

 

Using the heater as a portable appliance 

 

·

 

Place the heater face down on a scratch-free and stable 

surface, to prevent damage to the paint finish or the floor. 

·

 

Run the 2 x foot screws through the bottom of foot, and align 

with the screw holes on the bottom of heater. Ensuring the 

long end of the foot is at the front of the heater. 

·

 

Tighten the 2 x foot screws to attach the foot to the heater. 

·

 

Repeat same procedures to fix the other foot. 

·

 

Once you have finished fixing the feet, turn the heater right 

side up.   

·

 

Place the fret on the front and bottom of heater as well as 

decorative coals on the fuel bed. 

·

 

 

Dimension 

Minimum 

Maximum 

Width 

390mm 

483mm 

Height 

555mm 

590mm 

Depth     

110mm 

125mm 

Содержание 2599M










Отзывы: